Page 4 of 62 FirstFirst 1234567814 ... LastLast
Threads 76 to 100 of 1542

Forum: Advanced Technical Discussion

This is not the "My laser is broken!!!" forum. Advanced technical discussion is for intelligent discussion pertaining to the advancement of laser technology.

  1. RF CO2 laser drive frequency

    Started by bwang, 11-21-2012 16:31
    3 Pages •
    1 2 3
    • Replies: 20
    • Views: 25,123
    02-09-2021, 18:51 Go to last post
  2. DIY lasers

    Started by CTesa, 01-25-2021 03:47
    • Replies: 3
    • Views: 3,380
    01-28-2021, 10:20 Go to last post
  3. Open Source Machine Learning Autoaligner...

    Started by mixedgas, 01-27-2021 12:09
    • Replies: 0
    • Views: 2,572
    01-27-2021, 12:09 Go to last post
    • Replies: 3
    • Views: 4,828
    01-08-2021, 19:24 Go to last post
  4. Advice for 405nm Laser Polygon Mirror Scanning Device

    Started by rajhlinux, 12-26-2020 12:26
    2 Pages •
    1 2
    • Replies: 16
    • Views: 31,033
    12-29-2020, 19:12 Go to last post
  5. Trying out high power IR diodes!

    Started by dar303, 03-26-2020 03:56
    6 Pages •
    1 2 3 ... 6
    • Replies: 55
    • Views: 127,322
    12-23-2020, 00:12 Go to last post
    • Replies: 6
    • Views: 6,073
    12-17-2020, 12:41 Go to last post
  6. Galvo blanking mounts?

    Started by masterpj, 12-04-2020 13:23
    • Replies: 3
    • Views: 3,971
    12-15-2020, 10:38 Go to last post
    • Replies: 0
    • Views: 2,577
    12-07-2020, 03:04 Go to last post
  7. RCA Ion Lasers

    Started by mixedgas, 11-16-2020 10:21
    • Replies: 4
    • Views: 4,003
    11-18-2020, 09:15 Go to last post
    • Replies: 11
    • Views: 30,933
    10-13-2020, 08:53 Go to last post
  8. Galvo connector pinout?

    Started by Elmi, 09-13-2020 10:44
    • Replies: 9
    • Views: 52,458
    09-15-2020, 09:00 Go to last post
  9. Epoxy Granite

    Started by mixedgas, 09-04-2020 06:10
    • Replies: 4
    • Views: 4,091
    09-08-2020, 09:33 Go to last post
  10. Galvo details for beginners?

    Started by Elmi, 07-16-2020 08:48
    3 Pages •
    1 2 3
    • Replies: 27
    • Views: 76,805
    08-26-2020, 15:40 Go to last post
  11. Phase Converter Troubles

    Started by MrNIFty923, 08-17-2020 18:19
    • Replies: 3
    • Views: 3,996
    08-19-2020, 16:57 Go to last post
  12. Learning about lasers over fiber

    Started by masterpj, 08-17-2020 09:10
    2 Pages •
    1 2
    • Replies: 18
    • Views: 40,608
    08-18-2020, 22:52 Go to last post
  13. Driving coherent matrix

    Started by javanam, 08-09-2020 00:01
    • Replies: 0
    • Views: 2,895
    08-09-2020, 00:01 Go to last post
  14. Any optics experts out there?

    Started by Junktronix, 07-07-2020 10:19
    2 Pages •
    1 2
    • Replies: 11
    • Views: 25,687
    07-13-2020, 13:06 Go to last post
    • Replies: 3
    • Views: 4,081
    07-08-2020, 12:31 Go to last post
  15. Any Cambridge 6800HP Galvo Gurus out there?

    Started by kclements, 04-23-2020 21:48
    2 Pages •
    1 2
    • Replies: 11
    • Views: 28,416
    04-25-2020, 20:30 Go to last post
  16. Ether Dream: new Ethernet DAC

    Started by j4cbo, 10-10-2011 22:44
    12 Pages •
    1 2 3 ... 12
    • Replies: 117
    • Views: 201,027
    03-12-2020, 13:15 Go to last post
  17. Turbomolecular pumps, are split pumps of any use

    Started by NobleGas, 02-19-2020 15:04
    2 Pages •
    1 2
    • Replies: 13
    • Views: 27,141
    02-25-2020, 15:43 Go to last post
  18. dj crossfader/mixer

    Started by maxcady, 11-21-2017 11:23
    2 Pages •
    1 2
    • Replies: 13
    • Views: 33,035
    02-25-2020, 05:41 Go to last post
  19. VD-II laser driver question, trim pots..

    Started by Draco, 01-26-2020 01:11
    • Replies: 1
    • Views: 3,553
    02-02-2020, 03:54 Go to last post
    • Replies: 0
    • Views: 5,407
    01-28-2020, 08:51 Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 20 replies or 500 views
Hot thread with unread posts
More than 20 replies or 500 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •