invert x- scanner

Hello ther,

First off all i am new her and wanne say hi to everbody: Hi :)
I am strelac from holland and i just start in ther world off lasers.

For now i have a question:

When you have 2 the same projectors and a one pangolin FB3. Is it possible to make a modification at de Ilda input for the X-scanner, so that both scanners do the same, but only the X-scanner do mirror movements.

I was think of making a switch on the projector so you can invert de X-scanner on that projector. When this possible, am i right that i only have to change the positive with the negative and the negative to the positive for the X-scanner.

When i am wrong is ther another way to do this with out buying a second FB3.

Thanks and greetz form holland.

Strelac

hello Strelac - and welcome
Yes you are correct you flip the + & - wires and the axis will flip - most scanners have a jumer on he driver that allows you to do this bit clearly this means its kinda permanent so requireing opening the projector up should you want it flipped back
A simple dpdt switch wired very similar to a reverse switch on a dc motor will do the trick for you
Rob

Hi, and welcome to the forums.

This is how to make a x-inverting splitter

Are you planning to visit the NLLEM in ilpendam too ?

Don't forget to update your location in your profile, so you are easily recognized by fellow dutch laserists.;)

there is no need to change the projector internals. you just need an ilda-adapter with one in and two outs and one of the outs with switched cables for x. but if thre is the pssibillity to change by jumper, it is easier to fix that way.

something like that:
http://img87.imageshack.us/img87/8333/ilda.jpg

diy: <5 bucks
ready: ~30 bucks

only works with differential wired scanners, not single-ended.

It should work fine with single ended scanners as well

are you shure?
i do not use single-ended scanners, but i think, you`ll get an earth short then.

Quote:

---

Originally Posted by netzhaut

are you shure?
i do not use single-ended scanners, but i think, you`ll get an earth short then.

---

That will depend on the controller not the scan amp. Single ended OUTPUTS are a pain!:(
I suspect Dave always has differential control outputs (as does Strelac in this case) but sometimes sticks single ended amps on the other end of the cable.>:)
Thus no zero volt cock-ups.*DZ

Cheers :)

Quote:

---

Originally Posted by stanwax

hello Strelac - and welcome
Yes you are correct you flip the + & - wires and the axis will flip - most scanners have a jumer on he driver that allows you to do this bit clearly this means its kinda permanent so requireing opening the projector up should you want it flipped back
A simple dpdt switch wired very similar to a reverse switch on a dc motor will do the trick for you
Rob

---

I second Rob's advice -
the most difficult part of this mod is drilling the hole in your projector case! :p

A nice additional benefit -
The invert switch makes it very easy to switch from rear projection (through a scrim) to front projection (projector in front of the screen) graphics shows without having to make any software changes...:D

Quote:

---

Originally Posted by Stuka

A nice additional benefit -
The invert switch makes it very easy to switch from rear projection (through a scrim) to front projection (projector in front of the screen) graphics shows without having to make any software changes...:D

---

That shouldn't be necessary anyway should it if using projection zones? You can just set your graphics projection zone up permanently as X inverted. If you ever need it not inverted its no more than a couple of clicks away from being changed during per=show set up. Beats trying to time flicking a switch when switching from beams to graphics during a show surely.

That said, a switch is damn useful if pairing projectors!

Quote:

---

Originally Posted by White-Light

That shouldn't be necessary anyway should it if using projection zones? You can just set your graphics projection zone up permanently as X inverted. If you ever need it not inverted its no more than a couple of clicks away from being changed during per=show set up. Beats trying to time flicking a switch when switching from beams to graphics during a show surely.

That said, a switch is damn useful if pairing projectors!

---

No "mid show" flipping required -
I just set it once based on where the projector is physically located.
(If I'm doing a show with beams and graphics, I'll usually - space permitting - try to use a scrim, so no projector or audience relocation is required.)

Works great!