My laptop has 4 USB ports. When I run Quickshow, I use them as follows:
1. Korg nanoKontrol
2. FB3 #1
3. FB3 #2.
4. Enttec DMX
I am thinking of adding a 3rd FB3. Might I need to add a powered USB hub, or would a 2-way splitter do?
Printable View
My laptop has 4 USB ports. When I run Quickshow, I use them as follows:
1. Korg nanoKontrol
2. FB3 #1
3. FB3 #2.
4. Enttec DMX
I am thinking of adding a 3rd FB3. Might I need to add a powered USB hub, or would a 2-way splitter do?
theres no such thing as a splitter... you either have a powered hub or unpowered (bus powered) hub
if you use a bus powered hub and plug too many things into it windows will notify you that the available power on that port has been exceeded
No? What's this then? I realise it's an unpowered hub too but "splitter" seems to be a valid term for such inline extensions. *shrugs*Quote:
Originally Posted by flecom
Hence my question. Which really translates to "given what I already run off the ports, might an extra FB3 be too much?". Which might require more info than I can gather (such as the PSU specs in my laptop). But if other people run with such setups then I'm probably ok. N'est-ce pas?Quote:
Originally Posted by flecom
like it says in the description its a hub :p
power for usb has nothing to do with the laptop/laptop PSU etc.. its all in the spec :)
USB spec says ports should have at least 500mA available... USB power is spec'd in "units" 100mA/unit... USB port should have 5 units available... a low power USB device (like a bus powered hub) use 1 unit... a high power device (ex external hd) uses all 5 units (500mA - realistically they actually draw more but thats neither here nor there)
the FB3SE specs say 100-300mA current draw... figure the QS should be about the same... so its kind of hard to call... the hub itself is going to draw some current (probably like 100mA at the most)...
I'd think you should be fine, worst case your out the cost of the hub which shouldn't cost you much
Cheers flecom, that's helpful stuff!Quote:
Originally Posted by flecom
no worries :)
I think you should be fine, USB is generally pretty forgiving... like I said, its spec'd at 500mA max but most of the portable 2.5" USB drives draw ~750mA
regardless I would like to know if it works, so make sure to report back :)
So you are saying your sound card DAC will have the same calibration for size and color, if you are on battery or plugged into wall supply. I have not found a laptop yet that it doesn't shift on when you switch between the two.Quote:
Originally Posted by flecom
thats something totally different...Quote:
Originally Posted by polishedball
when I say USB power I mean the amount of current a USB port can deliver to whatever is plugged into it is specified by the USB spec itself
I have not noticed my image changing from battery to AC power on a laptop but I will play with that, I have several laptops I can try that with... but it should not change significantly... if it is something else is is happening that probably should not be
most USB ports go directly to the south bridge, so really nothing should change between battery and AC power
Interesting, I always figured that is why you needed to tune for your machine with the max.wav as the voltage not amperage shifted, perhaps im lucky with more odd ball equipment that doesnt act right.Quote:
Originally Posted by flecom
max.wav?
the amperage should not shift, and really the voltage should not shift to the point its noticeable either but I suppose its entirely possible
second post down, it is used to set the voltages so you get as close as possible to true color modulation ans size.Quote:
Originally Posted by flecom
http://www.photonlexicon.com/forums/...-6829-p-2.html
FYI, I usually run 2 FB3's via an unpowered hub on a single USB port. I have run 3 off the hub on one occassion but in light of the above, I've probably spread it over an additional USB port or add a powered hub.
There are also power Tees for USB, that lets you insert just as much power into a USB wire as you want.
I just hooked up 3 FB3s, one QS and two SEs, to a 4 port USB hub with no complaints from Windows or BEYOND. I can't say how long they will stay up or be stable, but all three of them power up with no issues. I need more projectors to test furhter. *retardo