Group Buy - High Power Broad Band Dielectric High Reflector Mirrors

[Laserman532]

Dang guys, sorry for the delays, he promised me this week! ARRRGHHHH!!!!!!!!

[Laserman532]

Scheduled arrival 4-2 , cut on weekend , ship to you guys on monday.

KRAZER - Paid for 2 ea 4 x 4" mirrors - DO NOT CUT -good to go

Carlos- Paid for 1 ea 4 x 4" mirror - cut half 1 x 1 other half 1 x .5 good to go

DSLIJON- Paid for 1 ea 4 x 4" mirror -4- 1" x 1"s; and the 'balance', 1" x 1/2"s - good to go
LOGSQUARED-Paid for 2ea 4 x 4" mirrors - DO NOT CUT - have your address good to go

SWAMIDOG- Paid for 1 ea. 4 x 4" mirror - cut into .5" squares- have your address good to go

SUGEEK- Paid for 1 ea 4 x 4" mirror - cut half into 1 x 1" squares other half .5 x .5 - good to go

If this is not what you guys understand...get in touch with me immediately!

dang this has taken forever, I apologize but vendor assures me quality product 400nm-680nm HRBBDR

[dsli_jon]

Hey Cap'n -

DSLIJON- Paid for 1 ea 4 x 4" mirror - NO CUTTING INSTRUCTIONS YET -

...Uh, I guess you did a 'flyby' over Post #39?

PM ME YOUR ADDRESS

OMG OK DONE!!!

Thanks, Cap'n.... you da Man...
j

[Laserman532]

Well the mirrors came in today and with a short learning curve (learned on my mirrors) I was able to successfully scribe and break all of your mirrors as you requested. I only sacrificed about 2 sq inches (oh well if you are going to make an omelet ya got to break a few eggs) I think you all should be happy with your end results. Anyway they all went in the Post Office today and you should see them monday or tuesday. Thanks for being a part of this group buy and apologize for the delay.

[sugeek]

Pat,

Thank you for all the work you put into this groupbuy! Delays are not an unexpected thing, but you being a respectable businessman were honest and open about the process. I look forward to reflecting on these in the future.

=Adam

[300EVIL]

Well the mirrors came in today and with a short learning curve (learned on my mirrors) I was able to successfully scribe and break all of your mirrors as you requested. I only sacrificed about 2 sq inches (oh well if you are going to make an omelet ya got to break a few eggs) I think you all should be happy with your end results. Anyway they all went in the Post Office today and you should see them monday or tuesday. Thanks for being a part of this group buy and apologize for the delay.

OMG! that's like over 100 years bad luck!

[logsquared]

Thanks for all the effort put in on this. Its much appreciated. Looking forward to getting them.

I am going to cut my own. I have made a jig that allows me to get strait and square scribes. Any input you have learned on breaking them would be greatly appreciated. I have practiced on a 1mm mirror from a Polaroid camera with good success. Scribing them on the non-coated side seemed to work best. Did you scribe on the coated or non-coated side?

thanks again

[carlos3621]

Thanks to Laserman/Pat, for this GB.
I just received mine today,,,, cuts look great! , i now have plenty of Dichro / spares.

[krazer]

Mine came in as well, look very nice!

Do you by chance have the reflectance plot for them? I plan to take some measurements eventually, but it would be nice to see what they measured them at.

[Laserman532]

Mine came in as well, look very nice!

Do you by chance have the reflectance plot for them? I plan to take some measurements eventually, but it would be nice to see what they measured them at.

pm me your email and i will send you the pdf