Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: New Toys .... NEW TOYS !!!!!!!!!!!!

  1. #1
    Join Date
    Feb 2005
    Location
    Southampton, UK
    Posts
    166

    Default New Toys .... NEW TOYS !!!!!!!!!!!!

    New Toys .... NEW TOYS !!!!!!!!!!!!

    Don't worry I have googles.

    Attention:XXXXXXXXXXXXXXX
    Under proforma invoice CHIXXXXX,USD560,ILP-808nm-400mW 4sets are ready
    to ship. We are going to ship after be paid ,so please send us payment
    asap.


    Best regards
    Mrs Qian

  2. #2
    Join Date
    Feb 2005
    Location
    Florida
    Posts
    802

    Default

    Ahh , IR laser pointers I see...

    Kewl
    "My signature has been taken, so Insert another here"
    http://repairfaq.ece.drexel.edu/sam/laserfaq.htm
    *^_^* aka PhiloUHF

  3. #3
    Join Date
    Feb 2005
    Location
    Florida
    Posts
    802

    Default

    Forgot to mention,.
    I made my own once when I ran across a bad crystal set..I pulled them
    and realigned the lenses and...presto , IR pointer.
    I Think it was a lightvision pointer I did this too as it was a POS
    Now...think of some use for it?
    "My signature has been taken, so Insert another here"
    http://repairfaq.ece.drexel.edu/sam/laserfaq.htm
    *^_^* aka PhiloUHF

  4. #4
    Join Date
    Jan 2005
    Location
    lancaster Pa. USA
    Posts
    130

    Default

    a crystal set tester?
    Those who stand for nothing, Will fall for anything.

  5. #5
    Join Date
    Feb 2005
    Location
    Florida
    Posts
    802

    Default

    Possibly..if you could keep it very steady
    "My signature has been taken, so Insert another here"
    http://repairfaq.ece.drexel.edu/sam/laserfaq.htm
    *^_^* aka PhiloUHF

  6. #6
    Join Date
    Feb 2005
    Location
    Southampton, UK
    Posts
    166

    Default

    I have an Altasnova leadlight that has a blown diode. Do you think I would risk ruining the diode in I focused on the these 808nm units into it ? What do you think would happen with 500mw of pump into a standard crystal, 50 mw ?

    I was also thinking of swaping one of the driver boards from the 808nm units on to the old leadlight with the new diode, what do you think ?

    Gold

  7. #7
    Join Date
    Jan 2005
    Location
    lancaster Pa. USA
    Posts
    130

    Default

    I dont think you would damage the diode by the leadlight swap other than improper handling, the crystals might have a problem with it.
    i think you would be better off using the driver board that came with the 500mw than the stock leadlight driver, the leadlight is not made for the current the 500mw uses.
    Those who stand for nothing, Will fall for anything.

  8. #8
    Join Date
    Feb 2005
    Location
    Southampton, UK
    Posts
    166

    Default

    Yep that was the plan, assemble the 500mw diode and driver into the rear of the leadlight ?

    Do you think I would be better off waiting for the Casix before doing this ?

    Gold

  9. #9
    Join Date
    Jan 2005
    Location
    lancaster Pa. USA
    Posts
    130

    Default

    Depends on how impatient you are
    Those who stand for nothing, Will fall for anything.

  10. #10
    Join Date
    Feb 2005
    Location
    Southampton, UK
    Posts
    166

    Default

    OK so I am bound to try it before Casix (BC), I will turn the pot down to low and take it from there.

    Begal what do you make to the new mod from lasermod ? Have you got any ideas what hes talking about ?

    Gold

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •