just showing a new module that could use the CNI Baby Green Module
It is just for fun!
Measures 3.5 x 6 x 1.5"
Senior Member
Laserman532 Dual Red, Dual Violet and CNI Baby Green
just showing a new module that could use the CNI Baby Green Module
It is just for fun!
Measures 3.5 x 6 x 1.5"
Pat B
laserman532 on ebay
Been there, done that, got the t-shirt & selling it in a garage sale.
Jr. Woodchuckington Janitor III, Esq.
very nice. that looks a lot a configuration i've been mulling over.
have you tried any beam steering/aligning with your teensy mounts?
Originally Posted by Laserman532
suppose you're thinkin' about a plate o' shrimp. Suddenly someone'll say, like, plate, or shrimp, or plate o' shrimp out of the blue, no explanation. No point in lookin' for one, either. It's all part of a cosmic unconciousness.
Senior Member
Nice Pat.
That is exactly what I was wanting your new 45 deg mounts for.
Already got a 125mw 532 module (just need to convert it to analog)
Already got 2x LOC diodes and cube
Already got 2x PHR and cube
Already got 2x Flexmods
Already got dichros.......
Now I just need you to send that kit to me for completion and review. I'll be more than happy to pay postage.
Senior Member
No, take a 150mW 445nm nicha, 2 x 150mW 640nm, And 100mW 532nm and you have great 0,5W projector.
Nice design!
Senior Member
Can you still get the Nichia blu ediodes because every search I do seems to end with page not found.
Senior Member
Hey, then you even have a diode slot left! Might be worth it to add a dichro in the spot where the 405 cube should be and combine 405/445 for some amazing blues.No, take a 150mW 445nm nicha, 2 x 150mW 640nm, And 100mW 532nm and you have great 0,5W projector.
Nice design!
I like the 445nm's, but as it is, they're still quite expensive.
Nice work Pat! That thing looks sweet! If you ever need any help populating one... Let me know!
Senior Member
That's no good, it looks like you forgot to tap *2* holes in this one and it maybe the fact that I'm sat off to the side of my monitor, but the base plate seems to taper from right to left.
Also the black anodising seems more like very very dark grey
Doc's website
The Health and Safety Act 1971
Recklessly interfering with Darwin’s natural selection process, thereby extending the life cycle of dim-witted ignorami; thus perpetuating and magnifying the danger to us all, by enabling them to breed and walk amongst us, our children and loved ones.
Senior Member
nice one
nice looking peice of kit that pat
wish i could make them that tidy but just dont have the tools for the job
here's my effort thats in my latest project
measures 100mm x 100mm and has plate that sits over top of the diodes with the drivers on
the whole projector is only 200mm x 150 mm x 110mm
Senior Member
Badger1666, I think I got ya on this one (as far as size goes any way) hehe
200=(7.87") x 150=(5.9") x 110=(4.33), it is tough to make it small isnt it?
Mine was the third rev to get it to its final size of 3.5 x 6 x 1.5
We still have to see what andy-con comes up with
so you are using edge combining, im using cubes.
bottom line is yours will probably put out light and mine wont (i dont have the cash to populate it and make it work) I like building the mechanics of stuff, dont get me wrong, i would love to make it put out light but alas...no cash.
has anyone resolved if the CNI baby will modulate? and what is the cost of one?
I may save this thing just to build it up one day...had to wreck out the ocotomom to make it haha
Pat B
laserman532 on ebay
Been there, done that, got the t-shirt & selling it in a garage sale.
Posting Permissions
Reply With Quote
300EVIL
