Results 1 to 10 of 10

Thread: Where to find a ILDA Breakout board?

  1. #1
    Join Date
    May 2008
    Location
    Portland, Oregon
    Posts
    130

    Default Where to find a ILDA Breakout board?

    I looked on ebay but the only ones I could find look really cheap. I thought someone on here was selling them but I could not find it in the search.

    Thank you much,

    James

  2. #2
    Join Date
    Dec 2009
    Location
    Alabama
    Posts
    183

    Default

    Check with user "LASERGUY". He may still have a few of DZ's ILDA bare breakout boards if you're up to soldering on the components.

    I've also used these http://www.winfordeng.com/products/brk25.php

    Hope this helps

  3. #3
    Join Date
    Dec 2007
    Location
    Bromley, Kent, UK
    Posts
    201

    Default

    Have you had a look at stanwaxs board? http://shop.stanwaxlaser.co.uk/ilda-...board-55-p.asp

    I got one from ebay http://cgi.ebay.co.uk/ILDA-Breakout-...#ht_571wt_1137

    It looks ok but it came with a 2 pin white connector that I have not been able to find the plugs for.

  4. #4
    Join Date
    Dec 2008
    Location
    veenwouden
    Posts
    2,580

    Default

    hello james

    Have a look at mccarrot his board. In combination with an ilda loopboard from SRS you have also al the safety,s and ilda in and out. The board from MCcarrot connects everything inside your projector with one board. The board makes also your projector
    EN60825-1 complient. It has connects your scanfail, scanneramps, drivers , and powersupplies to one board. It has also connection for your emergency switch and a reset circuit when power is lost from the net and suddenly comes back again.

    HereClick image for larger version. 

Name:	diff interlock.jpg 
Views:	36 
Size:	107.1 KB 
ID:	18036


    Here is the link with al the info


    http://www.photonlexicon.com/forums/...ight=interlock

  5. #5
    Join Date
    Dec 2006
    Location
    New Jersey
    Posts
    247

    Laser Warning I do still have some DZ boards

    I have 6 boards left and ready to ship them... they cost $20 (Including shipping)

    These are bare boards.... I have been so busy and just have not found the time to put a Jameco order together.

    Maybe this week I will order some parts and try putting them together. This will add to the cost of the boards.

    DZ did a very nice job with his design and they look like they will piece together very easily =)

    Let me know if any of you are interested...

    Laserguy

  6. #6
    Join Date
    Sep 2009
    Location
    Slovenia
    Posts
    79

    Default

    http://www.mdfly.com/index.php?main_...products_id=52
    Its simplest pin to pin breakout board,
    but they are offline for maintenace.

  7. #7
    Join Date
    May 2008
    Location
    Portland, Oregon
    Posts
    130

    Default

    Thank you everyone. Lot's to choose from now.

  8. #8
    Join Date
    May 2006
    Location
    Native Floridian
    Posts
    3,127

    Default

    Quote Originally Posted by LASERGUY View Post
    I have 6 boards left and ready to ship them... they cost $20 (Including shipping)

    These are bare boards.... I have been so busy and just have not found the time to put a Jameco order together.

    Maybe this week I will order some parts and try putting them together. This will add to the cost of the boards.

    DZ did a very nice job with his design and they look like they will piece together very easily =)

    Let me know if any of you are interested...

    Laserguy
    I seem to have a few parts left on the shelf for these, basically, the LED, switch block, resistor and a limited supply of the screw terminals. All that would be needed is the dual row pin header, single row pin header and right angle db-25. For anyone that orders one of the breakout boards from Laserguy, I'll send, free of charge, the parts I have available. I think I have enough screw terminals for the first 3 boards only.

  9. #9
    Join Date
    Dec 2009
    Location
    Alabama
    Posts
    183

    Default

    Quote Originally Posted by DZ View Post
    I seem to have a few parts left on the shelf for these, basically, the LED, switch block, resistor and a limited supply of the screw terminals. All that would be needed is the dual row pin header, single row pin header and right angle db-25. For anyone that orders one of the breakout boards from Laserguy, I'll send, free of charge, the parts I have available. I think I have enough screw terminals for the first 3 boards only.
    And DZ will have them shipped and at your door before you even ask him

  10. #10
    Join Date
    Jan 2007
    Location
    Sheepsville, Wales, UK
    Posts
    3,406

    Default

    more info on my board here - http://www.photonlexicon.com/forums/...ad.php?t=11373
    I dont call it a breakout board as its rather more than that but will make hookup of a projector an absolute doddle. This does provide the most flexible solution and has all the safety features included.

    Rob
    If you need to ask the question 'whats so good about a laser' - you won't understand the answer.
    -----------------------------------------------------------------------------------------------
    Laserists do it by the nanometre.

    Stanwax Laser is a Corporate Member of Ilda

    Stanwax Laser main distributor of First Contact in UK - like us on Facebook http://www.facebook.com/FirstContactPolymerCleaner
    www.photoniccleaning.co.uk

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •