Results 1 to 10 of 10

Thread: Review of the LaserCentury 150mW DPSS green (GL532T-150)

  1. #1
    Join Date
    Jun 2005
    Location
    SoCal
    Posts
    508

    Default Review of the LaserCentury 150mW DPSS green (GL532T-150)

    I obtained a LaserCentury 150mW TEC cooled 532nm green laser module...



    Boys'n girls... if you want a solid green with no compromises on
    optical quality, this is the laser you've been waiting for...

    Code:
    Manufacturer Specifications:
    
    Model Number:           GL532T-XXX 
    Output Power:           150mW 
    Output Wavelength:      532nm 
    Beam Mode:              TEM00, CW 
    Power Stability(RMS):   5% (over 2 hours)
    Beam Divergence&#58;        <1.5mrad 
    Beam Diameter&#58;          <1.0mm 
    Warm Up time&#58;           <5 minutes 
    Directional stability&#58;  <0.05mrd &#40;after warm up&#41;
    Ellipticity&#58;            >90% 
    Output noise&#40;RMS&#41;&#58;      20% around 50~200KHz 
    Beam width&#58;             0.1nm 
    Operating Temperature&#58;  5 ~ 35 degrees
    Modulation&#58;             >10KHz, TTL Mode &#40;as tested, analog and no mod. avail.&#41;
    Manufacturer MTBF&#58;      >10000 hours 
    Dimensions &#40;Laser&#41;&#58;     1.5" x 1.5" x 4" &#40;at base&#41;
    Dimensions &#40;Driver&#41;&#58;    3" x 1.5" x 7"
    Operating voltage&#58;      120VAC &#40;as tested, other options available&#41;
    First, let me state... I've been spoiled by the beam quality of large gas ion lasers.
    I've been less than impressed by most diode lasers I've seen, even the scientific units
    from Coherent and Spectra...

    Well this little module successfully forced me to re-evaluate my opinions on
    diode based laser technology, and did it at a surprisingly low cost!

    Power Levels

    This laser didn't dissappoint in the power category...


    177mW of true 532nm green!

    Now, one of the things the modern laserist needs to be aware of is that once a laser
    enters the Class IIIb range, manufacturers don't usually bother filtering out the
    "waste" IR beams. This is because the CDRH doesn't "care" as long as the
    class designation is accurate in defining the total power output (i.e. >5 - <500mW for Class IIIb).

    The second thing is that often, more than half the total power output of a filterless
    DPSS module is in the invisible IR range!

    The last is that is that vendors will include any invisible IR "waste" beam present in
    their rated power levels... This isn't inherently "wrong" because that total number is
    very important for eye safety considerations. What I do find less than ethical is that
    many new manufacturers are specifically leaving the IR filter off soley so they
    can claim higher power levels for marketting. That 200mW DPSS laser you bought off ebay
    may in fact only generate 80mW of usable green with the rest in IR!



    So, I was very pleasantly surprised to find an IR filter on this unit! Checking with
    an external IR bounce mirror confirmed that the onboard filter was working as designed.

    Beam Quality



    The laser didn't dissappoint in this category either... The beam diameter is the smallest
    I've seen in a laser of this price level... the divergence is so low that the beam was
    still point sized over 30 feet!

    Mechanical details

    Internals: This head is TEC cooled and maintains extraordinary stability for
    this class.



    Laser Head: This is where the cost savings start to show... While the head
    is build solidly, the annodization (the coloration) is amateurish and may show
    premature wear over usage... The first hint was that close examination
    shows the black anno to be more of a hue of green... Running a swipe
    of denatured alchohol over the base confirmed that the anno die wasn't
    properly sealed... Aside from the cosmetic detail, the laser head had a
    satisfying heft and was well built to very tight tolerances...


    The dimensions of the head are 1.5" x 1.5" x 4"

    Power Supply: The power supply is well designed but definitely
    could use a few improvements... Most notably missing is a key switch.
    For entertainment purposes, this means that in order to meet CDRH
    requirements, the end projector must integrate a keyswitch and
    power on delay itself... The other thing I noticed is that the modulation input
    feels like a tacked on design feature rather than an integral portion
    of the supply. The input is presented as a loose wire... I would have preferred
    to see a BNC jack or something similar... I may not have noticed, but
    it the modulation input was just too much of a stark contrast to the very
    nice and well designed connector which attaches the head to the unit.


    The dimensions of the power supply is 3" x 1.5" x 7"

    Modulation
    The unit supports TTL modulation at nominally faster than 10Khz,
    Some quick patterns show that it works just fine...


    Mounted in a conveniently spare scanhead system designed by ArcDevilz.

    What this all means

    This laser is a steal at any cost...

    Reality check
    Words are good, but what does it look like doing a beam show in real life?

    http://photonlexicon.com/hostedcontent/sloc/Show1.avi [10MB MMJPEG AVI]

    This clip was taken in my garage with the garage door open in broad daylight with the light streaming in!

    More images available at: http://photonlexicon.com/gallery/album30

    Fin.

  2. #2
    Join Date
    Jun 2005
    Location
    Los Angeles
    Posts
    263

    Default

    I can't believe how sexy and tight it fit into that case. My favorite was the video in daylight with a little haze. Okay when do I get mine?

    8)

  3. #3
    Join Date
    Apr 2005
    Location
    SOUTHAMPTON U.K.
    Posts
    1,357

    Default

    Excellent, do you have a link to them please?

  4. #4
    Join Date
    Jun 2005
    Location
    SoCal
    Posts
    508

    Default

    Hi Quazar,

    I bought mine off Spec for $550... I still drool when I think about it
    It makes the thinnest ribbons of light... drool...

    Anyways, he may have some left.

    Good luck!

  5. #5
    Join Date
    Jan 2005
    Location
    USA
    Posts
    457

    Default

    Ive got more now First come first serve.

  6. #6
    Join Date
    Feb 2005
    Location
    Florida
    Posts
    802

    Default

    Man..These are AWESOME lasers..

    Much better than the first batch of those others...
    I had to get one of these just like I did with those others..
    I can say for a fact these are much better assembled and more thought went into these..

    Also..a big PLUS is..THEY HAVE A DECENT IR FILTER
    did you guys catch that..yes.. from china too.

    And this filter wont blow out from the power too...
    Mine currently is a 225mW unit ... Very Stable once up to Temp.

    Very nice Blanker..and a smart one at that... It knows when its connected to the circuit.. And it seems to blank way up past 40khz..

    I do suggest mounting on a plate.. so the TEC wont hafta work too hard when used in a warm enviroment..

    I Love this thing,.. Damn brite for the power too..

    This cat CANT get enough of it!!!
    {


    *^_^*
    "My signature has been taken, so Insert another here"
    http://repairfaq.ece.drexel.edu/sam/laserfaq.htm
    *^_^* aka PhiloUHF

  7. #7
    Join Date
    Nov 2005
    Location
    Melbourne, Australia
    Posts
    3,702

    Default

    We had one of these die a couple of days ago.

    Upon pulling the psu to bits, a somewhat scorched bug was removed from under the pcb!!

    Looks like all thats cooked is the switch mode controller/chopper, but that raises the problem of getting spare parts down here in Australia.. Hopefully Laser Century will come to the rescue here, Otherwise im faced with purcasing a 2 dollar part from mouser, with 35 dollars shipping :roll:

    [edit] Laser centuary to the rescue, parts in the mail
    KVANT Australian projector sales
    https://www.facebook.com/kvantaus/

    Lasershowparts- Laser Parts at great prices
    https://www.facebook.com/lasershowparts/

  8. #8
    Join Date
    Sep 2006
    Location
    Beijing
    Posts
    85

    Default

    your cat ? how lovely! is it reaching the beam of pointer ? I can't see clearly .but his ability of jumping is marvelous , but I am worried , some times , like the big cat usuarally don't like playing any more , but it is diffrent , how lovely . I have joked my dog with the laser pointer , he really following the light beam everywhere . haha, so crasy ! :lol:

  9. #9
    Join Date
    Jan 2005
    Location
    Norway
    Posts
    1,303

    Default

    old thread but yea... I reallyh love that cat..

    The jumping skills is crazy
    Really funny to see when the cat land as well..

  10. #10
    Join Date
    Sep 2006
    Location
    Beijing
    Posts
    85

    Default

    yes, I see the fat cat mimi , but to my surprise , it can jump so high and so flexible . haha, I love animals , I also use the method to play with my dog . he trully going everywhere following the beam of laser pointer , at first he is curious to see it , when I put the laser pointer near him, he is so afraid of it, and run, but he will following the out put beam go everywhere . so lovely . :lol:

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •