Page 2 of 2 FirstFirst 12
Results 11 to 18 of 18

Thread: Buying or Building?

  1. #11
    Join Date
    Jan 2009
    Location
    Hannover, Germany
    Posts
    102

    Default

    This is a really nice and small projector! How much money and time did you spent?

  2. #12
    Join Date
    Jun 2010
    Location
    Zweibrücken, Germany
    Posts
    605

    Default

    @taggalucci
    what are the specs/cost on your (12mm diameter?) greenie there and where did you get it?
    How's the modulation?
    I'm also doing a couple of mini RGB modules and I'm still looking for a good 532nm aprox. 12mm module with <1.5mrad, better <1.2mrad.

    cheers!

  3. #13
    Join Date
    Feb 2010
    Location
    Melbourne, Australia
    Posts
    1,106

    Default

    Quote Originally Posted by Xer0 View Post
    This is a really nice and small projector! How much money and time did you spent?
    Thanks Though it's nowhere near as finished as I want!

    Well, time... about 36-48 hours duration, all up, including building Norm's RGB diode driver and troubleshooting that, planning the layout and drilling the baseplate, LPC-815 diode extraction, confirming nominal operating current for the 532nm pointer core and building the 660nm and 445nm diodes into Dave's mounts and soldering the diodes to wiring (including Lasorbs). In reality I started this last year and have not had much time to spend on this until recently.

    The RGB driver is still running off a bench PSU and the Spacelas PT-30K scanners I got from Dave don't work, so I'm trying to resolve that with Dave's supplier directly as Dave doesn't deal with them any more. So, that's now taking up quite a bit more time trying to get that resolved. In the meantime, I am using some DT40 Pros I have saved for another projector to test the driver's modulation. Until I resolve the scanner issue, I'm going nowhere fast!!! I was going to buy more of whatever 30k scanners I settled on for a couple more of these little guys. I guess I wont be buying and using any more of the PT-30Ks then!!!

    As for money, well...

    2 LPC-815 diodes
    1 A140 diode
    1 Blue Lasorb
    3 Red Lasorbs
    3 Dave's Diode Mounts
    3 Dave's Flex Mounts
    1 Laserwave 660nm PBS
    1 Edmunds Optics dichro (2nd hand)
    1 Laserwave dichro (2nd hand)
    1 Norm's RGB diode driver
    1 set of PT-30Ks + now whatever d!ckw4d at Spacelas expects me to pay for shipping, both to him in China for repair and back to me in Australia
    a couple of nuts and bolts, some wire, some aluminium sheet, DB-25 connector

    Prices for the above (apart from the aluminium which is free for me) as per suppliers on this forum or eBay.

    I will also need to buy:

    Compact +/- 24V and 8V PSU solution
    Heatsinks
    Fans
    IEC socket
    switches for mains and X & Y inverts
    key lock, push buttons and electronics for simple interlock circuit
    More aluminium for the housing + paint or other coating
    ...probably some other stuff I can't remember!

  4. #14
    Join Date
    Feb 2010
    Location
    Melbourne, Australia
    Posts
    1,106

    Default

    Quote Originally Posted by Solarfire View Post
    @taggalucci
    what are the specs/cost on your (12mm diameter?) greenie there and where did you get it?
    How's the modulation?
    I'm also doing a couple of mini RGB modules and I'm still looking for a good 532nm aprox. 12mm module with <1.5mrad, better <1.2mrad.

    cheers!
    http://www.dealextreme.com/p/200mw-5...v-11-9mm-26891

    I can get surprisingly reasonable modulation directly modulating the 808nm diode from the driver. Not convinced it does 200mW, maybe 150mW.

    The divergence is good, I haven't measured it - it is fine for a compact projector. I'm into beamshows, not graphics - though I think this 532nm module alone would be more than adequate for both.

    This is all about cheap and cheerful, no frills, no TEC, just throw away components. I like the results so far!

    I'll get some video up here, when I can, showing the colour depth and modulation.

  5. #15
    Join Date
    Apr 2011
    Location
    Laguna Beach, CA
    Posts
    81

    Default

    I also bought a 300mw china made scanner. Was not pleased with the low power. I have since swapped out all the lasers and power supply with higher power lasers and supplies. Almost ready to give it a run. Ended up costing me alot more than I thought it was going to..

    Steve

    Quote Originally Posted by Xer0 View Post
    If i want a RGB (445nm) Projector, lats say 1W + analog + 30kbps...

    How much cheapter will it be to build than to buy from the chinese?
    And how long you think i would need to invest time for building?

    Dafore i bought an 300mW RGBr one from China, it was not bad, but not that what i desire, so i sold it.

  6. #16
    Join Date
    Feb 2008
    Location
    Hungary
    Posts
    420

    Default

    Do you tips RGB sets 1000USD?

    What kind of only RGB analog module set purchase maximum 1000 dollars?
    Green 532, Red 650 or 642 and Blue 445 sets.

    (I have the Scanner and RGB optics...etc. )

    Thank you for a tips,

  7. #17
    Join Date
    Feb 2008
    Location
    East Sussex, England
    Posts
    5,248

    Default

    Buy a Chinese laser with good optics mounts and a decent case.
    You then have the basic building blocks to swap out laser modules and scaners at a later date as funds permit.
    Try and get a case with some 'growing' room too.
    Frikkin Lasers
    http://www.frikkinlasers.co.uk

    You are using Bonetti's defense against me, ah?

    I thought it fitting, considering the rocky terrain.

  8. #18
    Join Date
    Dec 2009
    Location
    MI, flint, farmington hills
    Posts
    569

    Default

    Yes im in the final stretch of build my new 2.5W projector and for a first timer one of the 250$ 500mw reke projectors are a great base.
    Yes you will end up replacing 90% of it.
    But you will have a working base.
    So you can do upgrades in small steps and still have a working projector rather than going on full steam.
    And you can sell the guts of them.
    There are good uses for the old galvos and lasers you wont make your money back but it helps.
    You will find projectors are alot of money.
    But with the new 635nm diodes and the 445nm diodes its helped to lower the cost.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •