Page 4 of 4 FirstFirst 1234
Results 31 to 37 of 37

Thread: Graphics Projector - by definition

  1. #31
    Join Date
    Jun 2010
    Location
    Australia
    Posts
    3,733

    Default

    I have watched this thread in disbelief... No one really understands what the REAL requirements for a graphics projector are, so I shall enlighten you all.

    The defining elements of a real graphics projector are simple and can be identified by the following:

    1. Typically includes a reference to "Cartoon" support. Only projectors supporting the iCartoon API 2.3 or higher should be considered.
    2. Must include DMX capabilities with at least 128 gobos.
    3. Typically includes iShow - a fundamental key to good graphics projection.
    4. Typically sold from China.
    5. Internal inspection typically reveals Dichros are glued in place to reduce movement and mis-alighnment.
    6. Graphics Projectors are often bundled with bubble machines and/or LED Par cans.


    There. Now you know.
    This space for rent.

  2. #32
    Join Date
    Oct 2010
    Location
    Athens, Greece
    Posts
    1,930

    Default

    i have been thinking about a combination of a bubble and fog machine
    i like my bubbles with smoke inside
    makes some nice atmospherics when they pop

    did some experiments too, but then i quit smoking and the projects was binned...

    and i have a certain "german" graphics projector here that pisses all over your chinese one
    i dare not post the specs as i don't want to stir waves of jealousy
    "its called character briggs..."

  3. #33
    Join Date
    Feb 2007
    Location
    Fort Mill, SC USA
    Posts
    1,521

    Default

    Quote Originally Posted by flecom View Post
    445 when corrected and run through a pinhole can also have a nice small tight round beam, I know I have done it... you will have a lot of losses, but it does not matter as you will have more than enough
    Sorry to add to an old post, but I ran across this nugget of wisdom while trolling for beam characteristics of various wavelengths in preparation for an upgrade to several of my RGBs. It is a simple solution that never occurred to me before I wondered if it could be done to a 635nm beam to resolve a similar problem.

    So in short, I attempted it with a situation on a primarily graphics projector that has a 635nm in I got from Marc that was doing double the power I had purchased. (Not that I looked at a gift horse in the mouth . . I had been using adjustment pots from StanWax to cut down on the reds. Unfortunately, cutting the mod voltage by about half using this approach results in a red diode that fades to zero much quicker than the green and blues did. Resulting in an uneven fade from white to black.

    So using the pinhole idea, my hope was to use this tip to cut my 635nm power by half (maintaining full analog range characteristics) and make that over-sized square beam overlapped more evenly with my tight 473 and 532 beams in the same rig. In the end I got this:

    S2040004.JPG S2040007.JPG

    That's a pretty nice white beam to the eye, but it retained the shape characteristics that it had before. The hole the 635 is projecting through is about 2.25mm diameter. The beam is supposed to be 4-5mm at the aperture, so I'm confused. Does a 635 tighten down a bit after the aperture and then diverge back out allowing that large square beam to get through? Also just to note, that green stripe in the picture isn't misalignment, its a crystal problem that only shows when projected onto a surface. I still need to correct or replace that problem.

    Is the only solution to get an even beam overlap between 8 and 15 meters when using 473s and 532s a purchase of a 660nm red?? I was really hoping to avoid this as the 660s are really pricey and comparatively dim . . .

    -David
    "Help, help, I'm being repressed!"

  4. #34
    swamidog's Avatar
    swamidog is offline Jr. Woodchuckington Janitor III, Esq.
    Join Date
    Nov 2006
    Location
    santa fe, nm
    Posts
    1,545,836

    Default

    david,

    how much red power are you interested in? combining two single mode 638nm diodes with decent lenses through a pbs cube will give you a ~250-300mW of red with excellent beam specs. much better than anything you will ever get with the flashlight high power multi emitter diodes.

    https://sites.google.com/site/dtrlpf...le-mode-diodes


    Quote Originally Posted by dkumpula View Post
    Sorry to add to an old post, but I ran across this nugget of wisdom while trolling for beam characteristics of various wavelengths in preparation for an upgrade to several of my RGBs. It is a simple solution that never occurred to me before I wondered if it could be done to a 635nm beam to resolve a similar problem.

    So in short, I attempted it with a situation on a primarily graphics projector that has a 635nm in I got from Marc that was doing double the power I had purchased. (Not that I looked at a gift horse in the mouth . . I had been using adjustment pots from StanWax to cut down on the reds. Unfortunately, cutting the mod voltage by about half using this approach results in a red diode that fades to zero much quicker than the green and blues did. Resulting in an uneven fade from white to black.

    So using the pinhole idea, my hope was to use this tip to cut my 635nm power by half (maintaining full analog range characteristics) and make that over-sized square beam overlapped more evenly with my tight 473 and 532 beams in the same rig. In the end I got this:

    S2040004.JPG S2040007.JPG

    That's a pretty nice white beam to the eye, but it retained the shape characteristics that it had before. The hole the 635 is projecting through is about 2.25mm diameter. The beam is supposed to be 4-5mm at the aperture, so I'm confused. Does a 635 tighten down a bit after the aperture and then diverge back out allowing that large square beam to get through? Also just to note, that green stripe in the picture isn't misalignment, its a crystal problem that only shows when projected onto a surface. I still need to correct or replace that problem.

    Is the only solution to get an even beam overlap between 8 and 15 meters when using 473s and 532s a purchase of a 660nm red?? I was really hoping to avoid this as the 660s are really pricey and comparatively dim . . .

    -David
    suppose you're thinkin' about a plate o' shrimp. Suddenly someone'll say, like, plate, or shrimp, or plate o' shrimp out of the blue, no explanation. No point in lookin' for one, either. It's all part of a cosmic unconciousness.

  5. #35
    Join Date
    Feb 2007
    Location
    Fort Mill, SC USA
    Posts
    1,521

    Default

    Quote Originally Posted by swamidog View Post
    david,

    how much red power are you interested in? combining two single mode 638nm diodes with decent lenses through a pbs cube will give you a ~250-300mW of red with excellent beam specs. much better than anything you will ever get with the flashlight high power multi emitter diodes.

    https://sites.google.com/site/dtrlpf...le-mode-diodes
    Thanks for this, Swami,

    I hadn't considered 638s because I thought these were also square beams with higher divergence than 635s. So you are saying that is the case with multi modes (300mW diodes), but not the single modes (110mW)? This box is my lightweight primarily for graphics - 600mW in its current config. Half of that (320mW) is 635nm making for a nice white. I do have a couple red cubes sitting around that I could use as 220mW in that wavelength wouldn't cut it. So that's three diodes, 3 drivers, 3 lenses, 3 heat sinks, 1 PSU, right? Anything else I'm missing? I'm fairly clueless as I haven't built and modulated a diode yet. Any clue what the divergence and beam dimensions are after such a build?

    -David
    Last edited by dkumpula; 09-21-2012 at 13:53.
    "Help, help, I'm being repressed!"

  6. #36
    swamidog's Avatar
    swamidog is offline Jr. Woodchuckington Janitor III, Esq.
    Join Date
    Nov 2006
    Location
    santa fe, nm
    Posts
    1,545,836

    Default

    you'll be able to overdrive the diodes a little. i don't know what's safe, but i think there have been some posts here about safe power levels.

    if you've got 320mW of highly divergent flashlight red now, i think you'll be in good shape with two of those 635 diodes and a cube. you may have slightly less power, but you'll also have a tighter beam and you'll be surprised at the difference that makes.

    you could easily drive up to four off a single flexmod driver, but i'd start with two and see how you like it before getting too complicated.

    Quote Originally Posted by dkumpula View Post
    Thanks for this, Swami,

    I hadn't considered 638s because I thought these were also square beams with higher divergence than 635s. So you are saying that is the case with multi modes (300mW diodes), but not the single modes (110mW)? This box is my lightweight primarily for graphics - 600mW in its current config. Half of that (320mW) is 635nm making for a nice white. I do have a couple red cubes sitting around that I could use as 220mW in that wavelength wouldn't cut it. So that's three diodes, 3 drivers, 3 lenses, 3 heat sinks, 1 PSU, right? Anything else I'm missing? I'm fairly clueless as I haven't built and modulated a diode yet. Any clue what the divergence and beam dimensions are after such a build?

    -David
    suppose you're thinkin' about a plate o' shrimp. Suddenly someone'll say, like, plate, or shrimp, or plate o' shrimp out of the blue, no explanation. No point in lookin' for one, either. It's all part of a cosmic unconciousness.

  7. #37
    Join Date
    Feb 2007
    Location
    Fort Mill, SC USA
    Posts
    1,521

    Default

    Quote Originally Posted by swamidog View Post
    if you've got 320mW of highly divergent flashlight red now, i think you'll be in good shape with two of those 635 diodes and a cube. you may have slightly less power, but you'll also have a tighter beam and you'll be surprised at the difference that makes.
    I've got a Laserwave 635nm in there now. Runs 605mW average, but I've effectively cut it down for a nice white. I don't recall the specifics on this diode, but I'm pretty sure the divergence is fairly low (at least not that I can tell in the ~45 foot environment). Its just the 635nm initial beam size is so much larger than the tiny 473nm/532nms. (The pic I posted of the beam was at 2 feet.) Beams look great, but as it goes through a scrim, the 635nm beam does look sloppy. That said, I certainly get your point that tightening up the beam makes it much brighter to the eye.

    Quote Originally Posted by swamidog View Post
    you could easily drive up to four off a single flexmod driver, but i'd start with two and see how you like it before getting too complicated.
    Cool, good advice. I've actually been eying up the FlexMod P3 for a while. Any suggestion on corrective optics?

    -David
    "Help, help, I'm being repressed!"

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •