Winni@ goldenstarlighting.com

[goldenstarmimi]

Is the noise from PSU or fans or laser diode head? And the image is pusating and flickering , is it in auto mode or controlled by laser software , QS or LD2000? If you project many points of images which the scanner can't bare, it also has flickering. If once you turn on the laser, it has this situation, it seems the green laser diodes needs some minute to be stable, I have two 8W green CNI here, at the beginning, it also has flicking problem in test. But after some minutes, it is ok.
So there are only two possibilities, one maybe laser diode problem, one is the image you project is with many points. If you can send us video, it is better for us to solve the problem. And both green laser diodes are from DHOM, if from CNI or laserwave, it is much more expensive, so if you want to make very high quality show, I suggest you use CNI or laserwave green, in most times, price and quality is in direct ratio. But what I can say is that our price is very better than other factories if in the same material, quality is better as well.
Usually cusotmers buy laser for beam show or graphic show, some requires high quality , some is just used in club, so if you can let me know what you use the laser exactly, we will give you good advice on this.
Please send video or some information in detail to Winni, we will help you to solve the problem asap.

[BruceLavender]

Hi Winnie,
I just saw a video on You Tube of one of you're 637nM lasers can you tell me which one it is, as it did not give a model number.

[goldenstarmimi]

Very sorry, we can't open youtube and facebook in China. The new 635 red from laserwave <1mrad, it is better than 637 red,but color is nearly the same. This 635 just dveloped by laserwave, it is small size 3mm diameter <1mrad. As we know, there are many small module in 637, near aperture, you will see many points,and sometimes, it will be splited,which is normal problem for this red. So if you are interested in this, you can contact us. We are building two RGB2500 with this 500mw/635,G1000 , B1000 , all from laserwave, DT30 scanner, built-in Moncha.net software. If you are interested in this, please feel free to contact Winni.

[db3306]

Hi Brooks,
We hope you can try this company,
Laser, Scanner,etc.

http://www.brandnew-china.cn/product....html#products

Not very nice to hijack someone elses good reputation thread with their own business... Just sayin.

[Ninebar]

Im a newbie here on the forum and to laser shows, my only previous posts where in relation to buying lasers from a reccommended manufacture. I went ahead with the reccomendation of goldenstar lasers; and have ordered:
2x super rgb2000's
QS+ FB3
Ilda cable

Winnie was more then helpfull through out the whole time. Emails went back and forth untill we came to a final agreement. I found there prices are very competitive and i got a whole lot more for money in comparising to buying from the likes of leading manufacturers.

Have been following my DHL tracker religiously and am awaiting impatiently for my gear to arrive!!

[laserLips]

Wow Jenus. Do all DT40s go this wide or did you get the wide movers?
Graham

[norty303]

I'm assuming from his post it was the DT40 wides (as he states DT40W, and the thrust of his post is about them not supplying the specific cut away block for the wides)

[laserLips]

I see thanks Norty. Sould read more carefully.
Graham

[goldenstarmimi]

Our QS is original from Pangolin company, don't worry about this. But I also heard someone in shenzhen develop a copy QS, I haven't seen it so far, the price is cheaper, around 1800RMB, hehe. Anyway, QS is not so expensive, it is better buy original one.

[Speculative Lasers - Dan]

winni a guy named Graham from taiwan is going to contact you about 2X rgb 1500 lasers, i recommended your company and service, he was worried that your site doesnt ship to Taiwan?

Dan