Results 1 to 6 of 6

Thread: repumping a krypton tube or an Argon tube to whitelight

  1. #1
    Join Date
    May 2009
    Location
    Sacramento, California
    Posts
    610

    Default repumping a krypton tube or an Argon tube to whitelight

    So Ive got a question.
    If I were to have an ion tube pumped to whitelight, which would make a better tube for reprocessing into a mixed gas? Im thinking of all the parameters and existing parts in the laser head-magnet/resonator assembly (optics, brewsters (quartz windows-vs fused sillica,ect.). Would a Krypton or Argon tube/head work better? Why would one or the other work better?
    Thanks,
    Nate.
    Will there be three phase!!!!

  2. #2
    Join Date
    Nov 2007
    Location
    SoCal / San Salvador / NY
    Posts
    4,018

    Default

    I'd go w/ an Argon, cause the bore is typically slightly larger = more power... 'Course, this depends on tube-model, etc.. I'm sure the 'P'fessor' will pipe-in, soon...

    ciao
    j
    ....and armed only with his trusty 21 Zorgawatt KTiOPO4...

  3. #3
    Join Date
    Jun 2009
    Location
    Nebraska
    Posts
    168

    Default

    Just for the sake of variety availability of said variety, you may be able to more easily find an argon tube (functioning/non-functioning) from the fee-bay that should have appropriate parameters.

    Finding which of the many tube has those parameters also depends on how much power you want, how many/which lines you want to see and perhaps the stability of each.

    Krypton should be just as well, however you might not have as many options on deals out there to work with. :/

    I'm also not sure that every tube can be re-filled without destroying the tube itself.. not all of them were made to be re-gassed by just anyone, so I suspect that a larger brand name tube would more likely be made with re-gassing in mind.

    *Eagerly awaiting Steve's reply


  4. #4
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    RANT MODE ON. Mixed Rant, in no order, for I am exhausted this week, so this rambles and its Midnight.. But you'll get the idea.

    Deal of the century. Only for you Mr W. I need to run up and pressure adjust my TWO I90MRA (Hint, Hint) tubes or get rid of them. Storage Space, the Final Frontier, to boldly follow Parkinson's Law..... And they do take up lots of space...

    I would prefer to do this with 3 phase, instead of 220 single. While I work on medical widgets that use 3 phase, my current employer, unlike my past employer, takes a DIM VIEW (pun intended) of my wanting to borrow lab space.

    My past employer could not wait to see what new colors I could come up with, including a few KR lines he had never seen at the premier laser research university in Russia, in Siberia.. So I used to have access to power, and the employer's tubes did some strange lines that were not normal obtainium. Well, after we experimented on mine. (New job is no where near is fun, procedures, documented procedures, must blindly follow procedures )

    So call me, I will tell you what to buy that has the right kind of fill system on them and where to look for them.

    Get it here with optics (Can tell you where to get those too, he has a pile of them :-) )

    Dont need the resonator, have the magnet, just the raw tube and optics. Its a tough ceramic tube, so no worries.


    ~14% premix is on the shelf, roughly the mix ratio used in the famous excess red Color Pros. I have about 550 PSI left of it in a D2 sized bottle, if it has not leaked much. It should not have leaked, it has a 3/4" solid brass plug where the regulator goes. In fact, dont ask how this happened, but my main bottle of mix says "Custom made for ***** Lasers by Spectra Gasses" on it. I also have pure argon and krypton. Then using skills honed by a few years of practice and a vacuum system that on a good day can reach 10-8 torr, I will pump your tube.

    The trick is how it gets resealed, and how it does not see air when opened, and those who have read my writings for years know I don't discuss those little tricks in detail, which cost me megadollars to learn. The tool was 1800$ five years ago, and I suspect its cost has doubled. Some one else paid for mine, which is part of why this is quiet. If you don't have the tool, you'll be lucky to get a week of shelf life from the tube, so its critical.

    Now here is the rub, you pay for a weekend or two of Genny rental, and Genny is a gasoline or diesel, not a Jenny, which either comes with nasty diseases when rented, or is a female donkey, depending on which Wiki you read... I really dont need the Donkey, anyways.

    I would prefer you see the tube lase before it gets here, or at least starts.


    You also pick up the cost of the disposable Swagelok fittings. (About 20$)

    Sound like a deal ? If I remember right you have one of those sealed prism ended Kr tubes I've always wanted to play with...

    Dang antidepressent makes writing fun...

    PS PS (Note to "Script Kiddies" who think they will try this with just a rotary pump and put it on "MeTube", that percentage changes with bore size and length in unpredictable ways, and some pre/post processing of the cathode is in order.SO dont go buy a 135$ disposable C4 tank of mix from "Dubious Lazer Gazzes" in Philly, it wont work! C4 tank fittings can't be backflushed with argon to get rid of the air. The good stuff is 770$ a tank, plus 135$ Hazmat shipping. The regulator is designed to be flushed with a cheaper pure gas, and that little feature is non-standard unless you work in a chip plant. Besides, the oil from the rotary pump will stop you in your tracks.)

    Hum, 550 psi in 1.5 litres expands to roughly PV(550) * NRT = PV(14) NRT at atmosphere where V = roughly infinity if you just let the gas out (I'm too tired to do the correct math and dont care how much a ballon holds) = some very expensive balloons if you dare...


    Steve
    Last edited by mixedgas; 12-19-2011 at 21:40.

  5. #5
    Join Date
    May 2009
    Location
    Sacramento, California
    Posts
    610

    Default

    Steve! Wowzers!
    I gotta think that all thru for a minute. *whew*
    Will there be three phase!!!!

  6. #6
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    Translation, I was having fun with creative writing last night, which I cannot do very often, my job is a &itch and sucks up time:

    Send me a working tube, or a pile of maybe working ones. I'll do a "Chop and Pump" which is NOT a rebuild, just a very complex refill process.

    Get some optics, I'll help you locate them

    Give me a week or two notice to get my vacuum system up and to tig weld onto the Tube(s) secondary (yes, there are two) fill stem(s) and test for leaks. It can take 48 hours for the system to "clean up", as it has not ran in a while.

    It takes 8 hours to clean up the vacuum on the newly installed piping. (this just needs 220 single to run the pumps)

    It takes 4-8 hours to adjust the pressure, clean up the cathode and get the tube to strike, then to adjust the pressure while running. Yes, the huge metal vacuum station has a special insulated pipe section, so I can adjust up/down with the plasma lit. If that insulator breaks down, or the pressure in the fill system gets way out of "nominal", it can "terminate with extreme prejudice" the laser PSU.

    Then you need to align it once it strikes.

    I have this bizzare tool that seals it. (The tool is a trade secret)

    My spare time is limited.

    I have tubes to run of my own.

    YOU Rent the generator as I'm doing this in the basement.

    My job needs a 55 hour week, so my time is limited.

    I'm blasting max money into the empty 401K right now, so I have no budget to rent a generator.

    The way I do it, the tube never sees air unless something goes WAY wrong.

    You want I90 Medical ReEntrant Anode (I90MRA) or I90MK medical Krypton (If you get a MK, I need the special series magnet, too), or a I90 (need the whole head for that one) . Under certain circumstances a 164 or 168 is acceptable, and some I60s or I70s with the tubes without crushable fill capsules. If its 164-168 will be VERY expensive to ship, VS a ceramic tube, and I need the exciter if its a SP. SPs are risky, the refill takes the gas through a long, thin, metal tube with a .040 or so bore. Gasses at low pressure do NOT like to flow through narrow tubes, it can take DAYS to get that right.

    Thats one hell of a deal, 1500$ or so worth of services (Well, that is what I used to charge in the old days) for the price of a Genny rental.

    Generators around here are cheap right now, in the winter no one rents them.

    (I get tired of people telling me they can do this, every time I post, and there are perhaps 10-12 places max in the world that can do this. The reason being skills and practices, not tooling. Nearly every university over 10,000 students has the proper pumps, but not the sealing tool. Every time I post about this, I get PMs or emails from people telling me this is not art, and is easy. I've got it down to moderately easy, and get it right about 5 out of 6 tries. There is one part of this process that I get into a cold sweat about 10 seconds AFTER I complete it. Hence the rant!)

    Steve
    Last edited by mixedgas; 12-20-2011 at 05:47.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •