Results 1 to 7 of 7

Thread: 2kW Roots Blower Trumpf

  1. #1
    Join Date
    Oct 2011
    Posts
    89

    Laser Warning 2kW Roots Blower Trumpf

    And now for something completely different ... heres a few photos of my 2kW roots blower Trumpf CO2

    First up, half of the resonator. This is actually 4 flow tubes with the RF exciter blocks clamped on externally. The blocks are the things with the water pipes attached. The copper strip is the incoming RF from the matching unit below the laser.

    2886110252_0f3e5275f3_z.jpg

    Biggest problem with these old things is waterleaks ... and those fittings which become brittle over the years and fail.

    Here is the business end where the fun begins the ouput coupler is beyond that big tube with the slanting cut to the end and a blue pipe, the thing like at bean-can with a black pipe is the beam dump, operated by a small pneumatic cylinder below.

    What you can see if you look to the right of the output coupler, you can see the power meter on the back of the rear mirror .. the laser has 4 tubes, so the rear mirror and the output coupler are on the front .. below those two you can see the pair of 45 degree horizontal fold mirrors on the lower two tubes, there are similar 45 degree fold mirrors on each vertical pair of tubes at the other end.

    Note how the power meter is on the back of the rear mirror ... at these power levels the mirrors allow a little radiatin through, not much, fractions of a percent, but with 2kw CW going up the pipe, there is enough leakage to allow measuement of the power in the beam.

    2886109580_d0666a856c_z.jpg

    You'll notice the output coupler and all the mirrors have black watercooling pipes. These are in the "aluminium" water circuit, there is a seperate "copper" water circuit for the copper based parts (like the RF generator)

    This (below) is a shot of the roots blower ... the big pipe is the gas flow from the laser, the square silvery block is one of the heat exchangers before the blower.

    2886108962_7610efd63a_z.jpg

    Below general shot of the resonator .. gas flow pipes to the blower clearly visible. The temperture guage on the blue box inthe background is the chiller. Notice how the large pipe in the centre (which is hot gas leaving the laser) has balck water pipes ... its doubled skinned here, as the exit gas is HOT. The two smaller pipers are the cool gas return to the ends of the laser. Yuo can just about see the grey metal box at the back of the laser where the RF comes in. Whenever it gets a leak, guess where all the water end up?

    2886108414_1a053a803f_z.jpg

    Next up, back of the RF generator, the copper pipe is the RF output, through the silver box (SWR meter) to the black "heliax" rf feed. The cavity presents different impedances before and after plasma striking, so the balck RF cable has to be a specific length to present a reasonable match to the transmitter under all conditions. You'll notice that black "walking stick" shaped copper pipe .. thats the water cooling return pipe in the "copper" circuit, the sliver block on the end is a flow meter .. they sensibly monitor the flow out of the RF valve, rather than in, just incase a leak develops.

    2886107654_bb5581e0f7_z.jpg

    Of course, the thing needs a mixture of gases, here the gas bank He (brown), N2 Grey/black and CO2 ... all laser grade of course. The mixer block for these is under the left hand end of the resonator, near the vacuum pump. The laser purges to atmospheric pressure during the shutdown cycle, with gas mix. You just have to wait for the vac pump to suck it down again during startup.

    2885271137_631ddb9e50_z.jpg

    Here is the logic rack that keeps it running ... the big box at the bottom is the variable frequency drive that runs the roots blower.

    2885268669_63ca7ffbe5_z.jpg
    Last edited by rszemeti; 12-19-2011 at 10:38.

  2. #2
    Join Date
    Nov 2007
    Location
    SoCal / San Salvador / NY
    Posts
    4,018

    Default

    Cool...

    You should get in touch with Wayne Shaffer (laserwayne - http://www.photonlexicon.com/forums/...038-laserwayne) here on PL - he's one of our 'neighbors' in our
    NY shop / office-complex , and he knows CO2 systems like the back of his hand... He could prolly suggest a good resource for the 'seals', I've heard him say much the same thing, as-well...

    cheers...
    j
    ....and armed only with his trusty 21 Zorgawatt KTiOPO4...

  3. #3
    Join Date
    Oct 2011
    Posts
    89

    Default

    Not to worry on that one, It has now moved on to a new home, those where some pics i took just before it left.

    Trouble with big lasers like that is they take up a lot of space, so they are fun to have around for a while and mess with but unless you have a practical use for them, its best to pass them on and get something bigger in to play with. It had to leave so the Lumonics could move in

    2KW of CO2 is fun though ... happily pierces a hole in 15mm steel plate, no worries. And for the record, it really is best to keep your fingers out of the way at this sort of power level, while a little baby 100w CO2 will leave a bit of a burn .. 2kW will go down to the bone or worse, I really would not want to find out. I have seen a full power pulse from a 300W Ferranti CO2 go clean through someones finger, nail, bone, the lot with no trouble .. could a focussed 2kW beam slice a finger off faster than you can pull it out of the way? quite probably.

  4. #4
    Join Date
    Feb 2008
    Location
    East Sussex, England
    Posts
    5,248

    Default

    'Roots Blower' ?

    Anyone want to elaborate for the luddites in the room?
    Frikkin Lasers
    http://www.frikkinlasers.co.uk

    You are using Bonetti's defense against me, ah?

    I thought it fitting, considering the rocky terrain.

  5. #5
    Join Date
    Oct 2011
    Posts
    89

    Default

    Yeah, no problem.

    Are you familiar with superchargers on cars? they are roots type blowers. Basically its a big pump, the ones on laser tend to be VERY big, because, at 28torr, there isnt a lot of much to pump about. The blower on this laser is about 12" long and 8" dia rotors, yet can be driven at 3000 rpm by a 3kw motor ... in air at atmospeheic pressure, it would need many many kw, but at near vacuum, not so much.

    random roots blower picture from the 'net:

    roots_blower.jpg

    The blower moves the hot He/N2/CO2 mixture out of the laser cavities, through heat exchangers and back to the laser again. Theres a lot of heat generated and you have to extract that energy from the laser somehow, or you get a melt down. moving the hot laser gas through geatexchagers and then back to the laser is the ways its done. Imagine 10kw of Rf going in, 2kW of laser coming out .. the other 7kW of energy has to come out as heat, and the roots blower is there to move the laser gas through the heat exchangers to do that.

    Roots blowers were used on this sort of laser, but the later Trumpf units have a "turbo molecular pump" ... which for all the world looks like a minature jet engine, I think I have one somewhere I'll dig out for photos if I can over christmas.

  6. #6
    Join Date
    Dec 2008
    Location
    Southport, UK
    Posts
    2,746

    Default

    Indeed, in automotive use a Roots blower can take several hundreds of horespower to drive.
    http://img62.imageshack.us/img62/3985/laser.gif

    Doc's website

    The Health and Safety Act 1971

    Recklessly interfering with Darwin’s natural selection process, thereby extending the life cycle of dim-witted ignorami; thus perpetuating and magnifying the danger to us all, by enabling them to breed and walk amongst us, our children and loved ones.





  7. #7
    Join Date
    Oct 2011
    Posts
    89

    Default

    Yeah, 28torr of Helium is much easier ... the thing sucks itself down to around 5 torr as a vacuum leak check, providing its gets lower than 8 torr, the computer will then turn on the laser gas flow and fire up the roots blower, and it lets pressure back up to 28 torr for running, sucking it down a little as it warms up to maintian the pressure. A constant flow of fresh CO2 mix goes slowly through the system .. I'm told in production use, they will chew through 4 bottles of helium a month, about 1 nitrogen and 1/4 of a CO2.

    You can muck about with the running pressure anxd the gas mix fairly easily by varying the relative pressures, I did have a little play with it before I let it go.

    These things can be picked up cheap if you want an industrial sized laser. I've seen ones with mis-aligned mirrors (due to some idiot turning it on full power when it was freezing cold and twisting the chassis) for as little as £2,000 ... mirror re-alignment is not hard, basically use a HeNe or pointer and some tube alignment plates to align the fold mirrors, and a collimator or a bounce-back test for the OC and TR, the nice thing about these lasers is the OC and TR are mounted in "plug and play" ally blocks, you can remove them for cleaning or replacement and drop a new one in from the factory with no alignment tweaks ... very handy in a production situation.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •