Results 1 to 5 of 5

Thread: Question on argon mirror distance

  1. #1
    Join Date
    Jun 2007
    Posts
    101

    Default Question on argon mirror distance

    Hi,
    What kind of effect or symptom do you get when an argon has it's mirrors at a different distance to factory spec?

    I had to change the alignment on my NEC3030 since it wasn't lasing when i got it.
    Luckily a gentle push on the mirrors gave a flash and i was able adjust the alignment screws to get the mirrors parallel again.

    The thing is, I'm not sure about the distance (moving all 3 screws together).
    What effect does that cause, or what symptom (if any) means the distance might be set wrong?
    Is it even that critical?

    Currently the laser outputs 488nm with a beam diameter of ~1mm at the head and 20mm after ~8meters.
    Last edited by Psi; 12-31-2011 at 00:01.

  2. #2
    Join Date
    Oct 2009
    Location
    Eindhoven, The Netherlands
    Posts
    921

    Default

    As far as I know, it doesn't matter that much, as long as the mirrors are parallel (or converging, if you have curved mirrors) so the light can bounce back and forth in the laser cavity.

    Having the mirrors further away does make them more sensitive to small (accidental) angular displacement, for obvious reasons.

  3. #3
    Join Date
    Jun 2007
    Posts
    101

    Default

    Thanks

    Any idea about the beam divergence?
    It is pretty old unit, is that likely just old age?

  4. #4
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    On a 3030, not that much, the front mirror is moderate radius and the rear is a flat. As long as you do not stretch/stress the vacuum bellows that seal the mirrors onto the tube, your good to go. It is sealed mirror, so not much you can do.

    You changed your divergence less then one percent.

    If you want, you can download the free PSST! software, I can give you some numbers, and you could simulate the divergence difference, but for the most part its too small to measure.

    You should read what we have in Sam's FAQ about "walking" the optics across the gain region for best power. However, I would not worry about it too much.

    Its in the Aligning Ion Laser Optics section, and also in the HENE section.

    Normally you do not touch the pivot screw, and just move X and Y, however, once you get good at finding lasing, you can move it back and forth a tiny bit. Again, do NOT stress the bellows.

    That does seem a litte fat, however consider that it was most likely designed for high divergence, those systems were customized for many customers. Is there dust on the OC or power pickoff dichro? IF it was in a copier/printer toner getting on the outside of the OC can make it fat via diffraction.

    Since those have not been produced for a long, long, time, Its amazing one is still running.


    Steve
    Last edited by mixedgas; 12-31-2011 at 08:45.

  5. #5
    Join Date
    Jun 2007
    Posts
    101

    Default

    Quote Originally Posted by mixedgas View Post
    Is there dust on the OC or power pickoff dichro? IF it was in a copier/printer toner getting on the outside of the OC can make it fat via diffraction.

    Since those have not been produced for a long, long, time, Its amazing one is still running.

    Steve
    Thanks, i'd not thought about the power pickoff unit, so yeah that could be the issue.
    I have removed it before but i don't think i checked divergence with it off. Will definitely try that and see what its like.

    Hehe yeah, its still running. I have no idea how much usage its had other than the hour meter which was disconnected but read 8186.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •