-
SDL-8110 question
Hello all I am looking for some information on a couple of Spectra Diode Labs units that I purchased.
I'v looked high and low for information on these units but to no avail. Just a couple pictures of incomplete units and mentions of the laser used in research.
I was able to get two units and a controller/Diagnostic unit. They 'seem' to be complete and connected correctly. I should say that I have very little experience in electronics and am working on a large learning curve.
I'v put some pictures of the laser and controller, as well as the error lights that are showing. When I engage the shutter the display on the controller goes dim and the shutter doesn't make any movement.
Not sure what 'OPT INTLK' refers to but perhaps the shutter.
Also from what I understand the controller board converts the 24V from the PSU into +5V and +/-12V. Again I'm not an electronics engineer so my uneducated guess would be for some reason the controller board is not getting the power from the PSU?
Any information would be of great help!
The unit in question...From what I have read...10W mid-IR. When I power it up the TEC is working as I can feel the cold and see condensation....
[IMG]
[/IMG]
[IMG]
[/IMG]
[IMG]
[/IMG]
This is the ONE photo I found of the same unit...this is missing some of the parts that mine has, but explains a bit about the laser.
[IMG]
[/IMG]
Lastly the controller/diagnostic unit back and front engaged with error conditions.
[IMG]
[/IMG]
[IMG]
[/IMG]
Thanks all for the help and taking a look.
-
SDL Laser
First, be careful once you get the laser running, the 10W of 808 will only look like a dim red. Even though the light out of the fiber it's diverging, it's enough to be troubling.
Second, the reason it's has a fault is because it doesn't have a fiber attached. If you look inside the laser with the top off, you'll see 2 wires(black/white) coming from the silver fiber connector. Remove this cable where it plugs into the header. Replace this with a small jumper, ie. the kind used in harddrives to select master/slave, and you'll be lasing.
What are you planning on doing with these? Saw that auction on ebay, but I already have 30+ of those...
-
Thanks for your help hologeek!
I will be very careful with the 10W when I do get it up and lasing. As for my plans it's just to get at least one of these units working. I haven't tinkered with this kind of diode yet and when I saw these two with the controller come up on ebay I went for it.
Now I was able to find an extra fiber cord and it screwed into the shutter with no trouble. I still get the OPT INTLK and 12/12/5V error conditions though. I also found the 2 wires you are talking about and they go to the top of the shutter. I'm not sure where I should 'jump' the cable to though. Do you think that the other error conditions are related to the opt intlk?
Thanks again for your help....I hate to go asking, but just couldn't find any information online for these units...only mention of them being used in research. Also if you may have some pictures of the wiring you are talking about and maybe the internals of one of your working units that would help a great deal! I'm a visual learner and still have that huge electronics learning curve i'm trying to get over!
EDIT:
Okay, so one problem solved through my own foolishness.....I took off the silver part to the fiber connection to see what was going on there. Seems there is a small spring trigger that know when a fiber connector is in. I couldn't figure out why my fiber wasn't triggering it.....then it came to me.......I had it in backwards! Geez, first time working with a fiber connector!. So the OPT INTLK error light is off now and that seems to be working.
I am though still getting the +/- 12V and +5V error lights, and when I open the shutter via the controller nothing happens except the LED screen goes dim and I get a small flash of 808nm and it fades out too. This is killing me, i'm seem so close to getting it working.
Edit 2: Hologeek, would you have any documentation for these units. The other laser I got didn't come with a PSU, from what I understand it is 24V but i'm not sure what Amperage it should be, there are so many for sale with differing values. Thanks again for helping with the fiber connection issue!
Last edited by 532withEnvy; 03-16-2012 at 18:06.
-
SDL laser
The 12v and 5v lights do not indicate errors, just that the power supply is working.
On the circuit board that has the shutter, just jumper the pins marked "SMA" Or you can remove the entire shutter/power monitoring assembly and jumper pins 4 and 10 on the 14 pin header on the main board.
I think your diode is dead. Is your 'Control Mode' set to 'Power' rather than 'Current'? If it's set to 'Power,' these units will ramp the current up past 36amps to the diode if you turn the current pot all the way to the right(max power). The controller is expecting to see some photons, and if the diode is dead these systems will ramp the current up to the max setpoint. Probably why you see a dim flash of light... Your red aiming beam should still light though.
Word of warning, just run these in 'current' mode. I would be very careful running them in 'Power' mode unless you want dead diodes...
If the diode is dead, these do make great 30+A laser diode driver & 10+A tec drivers...
-
Well it's a great weight off me to know the 12v and 5v lights are not an error. In that case you may be correct that I have a dead diode.
I'll twiddle with it some more to see what I can get. I still have the other unit without the PSU to try as well, so here's hoping for that one to work!
Thanks again for your help with this, the largest problems I'v found with getting these older, used lasers is finding information on them.
-
MMM...so I'm still getting some kind of drop out of power I think. My aiming laser is only giving me a flash as well. Now both could be cooked. What I can't figure out is that when I try to engage the shutter, the display on the controller goes dim, it's the same with engaging the aiming laser. The shutter doesn't seem to actuate, but I still get the dim flash. Even if the diode is dead, why would I get a flash through an un-engaged shutter(there is the motor on top and I don't see it move when I try to engage).
I also tried to hook up the PSU from the first unit to the other and got mostly the same results.
Hologeek....do you have any documentation, or ideas of what might be going on? It seems like even though I may have a bad diode, there is some other trouble going on with the two units.
(if these are just done, I may be interested in purchasing one of your working units if they are for sale)
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules