Help for laser show DiY

[megaton]

Hi Juanma

One for current and one for temp.
And more info here:

http://www.photonlexicon.com/forums/...en-China-laser

Cheers,
Ed

[juanma666]

Muchas gracias por la respuesta, visitaré ese enlace.

Juanma.

.................................................. .


Thank you for the answers.

Juanma.

[juanma666]

Llegaron los galvos de 30Kpps y he estado haciendo pruebas con la tarjeta que traían. De momento solo con el módulo de verde.
Tengo que hacer la base de aluminio para fijar bien todos los componentes y empezar a ajustar el sistema.

.................................................. .....................

The galvos of 30Kpps arrived and I have been making tests with the card test show. At the moment alone with the module of green.
I have to make the aluminum base to fix all the components well and to begin to adjust the system.






At the moment...













Best Regards.

Juanma.

[megaton]

Now the fun part.

Congrats,
Ed
PS the itch is in your body( o sea que ya te empezó esta adicción. ).

[JasonB]

Great work! May I offer one piece of advice because my project is EXACTLY at the same stage as yours is now; and mine has been there for almost a year. This is why:

Please use caution when installing and aligning your dicros! Wear safety glasses AND if you have analog lasers attenuate them (turn down the power) during alignment. It is VERY easy to catch a stray beam in your eye - safety first! Nothing is more disappointing than damaging your eye during a build, it really squashes the 'fun factor'.

If other PL's agree please translate if necessary. Had to use the great pictures to follow most of the build!

Have fun, exercise caution be safe at this stage of your build.

Jason

[LaNeK779]

well done!!

thanks for the pictures!!! I like this part of the build where everything is "open"

[juanma666]

Gracias a todos por la ayuda y el apoyo, en especial a Eduardo.

Tengo en cuenta todas las recomendaciones, consejos y críticas.
Solo es una prueba, ahora tengo que hacer la base de aluminio y empezar a fijar los módulos y los galvos; tengo un problema con el módulo de rojo (635nm/200mW) el beam es muy grueso y con mucha divergencia, no se si montarlo o comprar otro rojo de 650nm, pero quiero que sea muy visible, ¿qué me aconsejáis?

Todos los pasos de construcción los voy detallando en mi blog, para quien pueda serle útil.

http://highfidelity.es.tl/Inicio.htm



Saludos cordiales.

Juanma.

.................................................. ......


Thanks to all for the help and the support, especially to Eduardo.

I keep in mind all the recommendations, advice and critical.
Alone a test is, now I do have to make the aluminum base and to begin to fix the modules and the galvos; do I have a problem with the module of red (635nm/200mW) the beam it is very thick and with a lot of divergence, not you if to mount it or to buy other red of 650nm, but do I want that it is very visible, what you advise me?

All the construction steps go them detailing in my blog, for who can be him/her useful.

http://highfidelity.es.tl/Inicio.htm



Best Regards.

Juanma.

[juanma666]

Hello.

I am with the assembly of the components in the base.






Best Regards.
Juanma.

[juanma666]

I have some doubts it has more than enough connections of the Show Card to implement the blue module of 445nm; I am not sure of as putting the jumpers correctly.






And the second, what configuration Address Code interface, I have to select for connect the IShow LaserShow.




Show Card instructions:

http://www.te-lighting.com/eng/suppo...how%20card.pdf



Best regards.

Juanma.

[colouredmirrorball]

I didn't quite understand your first question, but normally you would just connect the blue modulation signal to the blue driver...

As for the second question, the user manual didn't mention how to set the DIP switches (addresscode), so I assume it automatically detects ILDA input. Once you connect the ILDA cable to your DAC (the iShow) it should switch to ILDA mode and project whatever you send to it with the computer.