Page 4 of 5 FirstFirst 12345 LastLast
Results 31 to 40 of 42

Thread: New Projector Project

  1. #31
    Join Date
    May 2009
    Location
    CA
    Posts
    116

    Default

    Do you think I should try those 100mm and 75mm lenses to fold the beam of my red laser? I've tried to make the beam as small as possible with the corrective lenses but still loose about 40% of the power after the 5mm mirrors on the scanners.

  2. #32
    Join Date
    Feb 2011
    Location
    New Hampshire
    Posts
    3,513

    Default

    Do you think I should try those 100mm and 75mm lenses to fold the beam of my red laser? I've tried to make the beam as small as possible with the corrective lenses but still loose about 40% of the power after the 5mm mirrors on the scanners.
    Are you using a quad or dual or single diode set up?

  3. #33
    Join Date
    Jul 2007
    Location
    west sussex uk
    Posts
    2,280

    Default

    before i buy any can you confirm i have the right part numbers please
    450nm one , NT69-887 .
    550nm one , NT69-900
    in th uk price is £79.00 or $126.00
    When God said “Let there be light” he surely must have meant perfectly coherent light.

  4. #34
    Join Date
    May 2009
    Location
    CA
    Posts
    116

    Default

    Right now a single diode, but going to upgrade to a dual soon.

  5. #35
    Join Date
    Feb 2011
    Location
    New Hampshire
    Posts
    3,513

    Default

    No. Actually the ones that I believe are identical with the Semrock models are:
    NT 86-390
    NT 86-393

    These are a little more expensive. I don't know how the other models you list compare. They might be excellent, I just don't know.

  6. #36
    Join Date
    Jul 2007
    Location
    west sussex uk
    Posts
    2,280

    Default

    dam wont be buying them just yet eek 140.00 GBP = 224.091 USD
    the uk edmunds is just to expensive me right now , trying to save for a 2w 532nm

    thanks for the part numbers planters
    When God said “Let there be light” he surely must have meant perfectly coherent light.

  7. #37
    Join Date
    Feb 2011
    Location
    New Hampshire
    Posts
    3,513

    Default

    OK. With a single diode or if you someday upgrade to a dual with a PBS/waveplate the size will be identical. Because you have a single stripe then all you have to do is reduce the width of this stripe. The already 2-3mm height will not present a problem fitting on a 5mm mirror at a 45 degree angle of incidence. The best, lowest cost and lowest loss solution would be to place the first cylinder lens in the expansion pair, closer to the diode and refocus the second cylinder to a smaller near field beam size. There is nothing wrong with moving this pair closer or farther from the diode to re-size the beam. The only down side effect is that the divergence will increase proportionally as the beam size is reduced and no combination of beam manipulation-optics will change this optical property.

  8. #38
    Join Date
    Jul 2007
    Location
    west sussex uk
    Posts
    2,280

    Default

    planters could you please look to see if any filters on this site may do ?
    http://www.longpassfilters.co.uk/

    many thanks
    When God said “Let there be light” he surely must have meant perfectly coherent light.

  9. #39
    Join Date
    Feb 2011
    Location
    New Hampshire
    Posts
    3,513

    Default

    I do not think so. As I read it, these are absorption glass medium filters as opposed to reflective dielectric filters. If you are looking to find an alternative to the costly filters above there are so many suppliers it is daunting. You might consider using the smallest diameter that will clear the beam or just use say one filter ( the one most down stream) this way at least all the lasers will benefit from the upgrade as to only two.

  10. #40
    Join Date
    Jul 2007
    Location
    west sussex uk
    Posts
    2,280

    Default

    Thanks for looking planters , in my projector i have the red nearest the scanners then blue ,then green
    The refelect red dichro is a newer laserwave one, and is good at passing green and blue the reflect blue one is not so good
    At passing green ,so thats the one i would replace , would the 466 filter be ok to still use as mine are in a different order ?
    Sorry to ask i am crap at optics can build modules ok though
    When God said “Let there be light” he surely must have meant perfectly coherent light.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •