Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: Question about DPSS diode temps

  1. #1
    Join Date
    Sep 2012
    Location
    Hannover, Germany Formerly Spartanburg, S.C.
    Posts
    20

    Default Question about DPSS diode temps

    Hi,

    Wondering what the different symptoms are of DPSS diodes being too hot or too cold? Which is worse? whats the ideal temp for them to run at? My green seems to get weak throughout the beam or with extended run time.

    Ex. If I have a circle projecting in yellow, its a nice deep yellow at the beginning of the circle, in the middle its orange, at the end is almost completely red. Not sure if this is temp related, but when the green has been running for awhile 5 mins or so, it gets dimmer and dimmer, if I leave it off for about 1-2mins. it runs a full power again.

    Steven

  2. #2
    Join Date
    Mar 2009
    Location
    New Orleans, LA USA
    Posts
    403

    Default

    sounds like different laser modules modulation differently...something like this would fix the problem.. http://shop.stanwaxlaser.co.uk/dz-co...oard-252-p.asp .. also you can try "ANALOG with long response" in your projector settings and tune your modulations to match....


    watch this video...start at 23 min

    10W RGB
    2x 5W RGB
    2x 3W RGB
    2x 1W Green
    ---------------------------------
    QM.NET, 2x FB3, LivePro, Beyond, APC40,

    kgblasers.com

  3. #3
    Join Date
    Sep 2012
    Location
    Hannover, Germany Formerly Spartanburg, S.C.
    Posts
    20

    Default

    Using HE laserscan. Ive already set all of the color correction. Someone recommended this board already on a different matter. Would still like to know what the temp symptoms are. The temp warning LED's seem to be on on the drivers for all colors.

  4. #4
    Join Date
    Jan 2006
    Location
    Charleston, SC
    Posts
    2,147,489,632

    Default

    DPSS blue lasers are more temperature sensitive than the greens are. If the blues get cold, the output drops off significantly. (The doubling crystal in a DPSS blue has to be warm, and the temperature band for optimal efficiency is very narrow.) I've seen a 100 mw blue drop to just 5 mw when operated outside in cool fall weather (45 degrees F).

    Greens are less sensitive to temperature changes, but they can fall off if they overheat. The next time you notice the green power falling off, yank the lid on your projector and see if the green module is hot to the touch. (Not just warm, but hot.) If it is, then you need better cooling.

    Adam

  5. #5
    Join Date
    Sep 2012
    Location
    Hannover, Germany Formerly Spartanburg, S.C.
    Posts
    20

    Default

    All of the diode modules are always cold to the touch. have even measured them at a 1 degree C below ambient. Im wondering if they might be too cold. Ambient Operating temp is usually around 17-18C sometimes cooler. I do a lot of stuff outdoors or in uninsulated and unheated "barns". last event we had 11C all night long. Even in the summer, here in Germany, its always cool at night.

  6. #6
    Join Date
    Jan 2006
    Location
    Charleston, SC
    Posts
    2,147,489,632

    Smile

    Quote Originally Posted by steven850 View Post
    I do a lot of stuff outdoors or in uninsulated and unheated "barns". last event we had 11C all night long.
    Hmmm... That's getting close to the 45 degrees F that I've worked with (and had problems). But I've never had an issue with my DPSS greens, just the blues.

    Try this: set your projector up inside where it is warm (75 degrees F or better) and run the projector. If the problem still occurs, then it's not due to temperature and you have some other problem.

    But if it works OK inside, then move it outdoors where it is colder and see if the problem comes back. If it does, then you may need to install a switch to turn off the fans, or even block some of the vents, in order to prevent excessive cooling of the internals when you use the projector outside in a cold environment.

    Adam

  7. #7
    Join Date
    Sep 2012
    Location
    Hannover, Germany Formerly Spartanburg, S.C.
    Posts
    20

    Default

    Gonna try heating the housing and disconnecting the fans. The blue is very low on power, I have the red and green turned down extremely far in laserscan. around 30% percent or so and the blue at 100% to try and get a good white. If the problem subsides while at a higher ambient temp, what all can be done to "calibrate" the projector for these low operating temps?

    I must point out that the problem with the green is 2 problems, one is the loss of overall power after extended runs, 5mins or so. The second is the problem of it dimming throughout the beam. It looks like the green is set to fade, as if the program was told to fade from yellow to red, but its suppose to be yellow all the way through. Happens with all colors. I will try and post a picture of a green square on a wall. you can clearly see the start and end point, the start point being at 100% output and the endpoint somewhere around 20%. It just loses power throughout the steps so to say, until the start point, then its all good. Same thing happens when I do a line, left to right. If I add points along the line, then it holdspower all the way through. Hopefully this clarifys it a little bit. Will post pics as soon as possible.

  8. #8
    Join Date
    Jan 2006
    Location
    Charleston, SC
    Posts
    2,147,489,632

    Default

    The color fade problem sounds like a modulation response issue, which is very common with DPSS lasers. A color board will help correct this.

    As for the loss of power from excessive cooling, there isn't much you can do beyond trying to keep the projector at a more stable temperature. If the projector is still usable even at lower power levels, then you could set it up in a cool place, run it until the power stabalizes, and then re-train your color pallete. But if you're using HE Laserscan software, I don't know what sort of palette options you have. (My guess is, not many...)

    Adam

  9. #9
    Join Date
    Nov 2007
    Location
    SoCal / San Salvador / NY
    Posts
    4,018

    Lightbulb

    Quote Originally Posted by buffo View Post
    ...As for...excessive cooling...you can...
    ...Go Chromalox! http://www.chromalox.com/productcata...ls.aspx?m=3596 - we've used these on much-larger projector-housings, where, just-because of the surface-area of the box, things would get 'outta-whack' from ambient thermal-differences w/no activity in the big-club, during the week... then, when the internals of the PJ would heat-up, from operation on the weekends, the 'differential-swing' would really whack it out.. So, discovered / installed one of these, with a 'regular-ol 'thermostat', ie:

    Chromalox_PL400.jpgThermost.jpg...really worked the charm.

    You can get these in really-small sizes (..ie: ever see the little 'heater-blankets' they often wrapped onto General Scanning G-120s / 130s, 'back in the day'? Yup.. same-stuff..) ..up-to a few inches, mounted to a nice L-bracket alum-plate, etc... Then, you simply use a thermostat to regulate the AC-power to these / shut-off set-points, balanced-by where your lasers seem to be 'happiest' for the conditions you're oft-operating in, and voilá... a 'happy place'..

    Obviously, you'll need a much-smaller / more-appropriate 'thermostat', for the air-space in the PJ-bx, or, even something surface-mount, that will help you achieve the delicate-balance likely to be the winner, here.. but, these puppies work quite swimmingly for helping 'manage' the balance, between hot / cold...

    fwiw..
    j
    ....and armed only with his trusty 21 Zorgawatt KTiOPO4...

  10. #10
    Join Date
    Oct 2007
    Location
    Vancouver, Canada
    Posts
    327

    Default

    Does the green work any better when set to 100% ? With the green's I've had, I found they didn't perform well when running at low powers for any period of time. Also, not sure if linear, but 30% of 5v is 1.5v, which doesn't leave a lot of room for modulation if it's locked to 30%. Fixing it would be easy enough, maybe add a beam splitter and dump 50% somewhere inside the case..

    As far as temperature, I had a laserwave 500mw which dimmed considerably in cold weather. Used to keep a few pieces of cloth and rubber bands to put over the intake fan on the projector to dial back the airflow.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •