Results 1 to 6 of 6

Thread: To all the diode nuts...

  1. #1
    Bradfo69's Avatar
    Bradfo69 is offline Pending BST Forum Purchases: $47,127,283.53
    Join Date
    Jul 2010
    Location
    Wilmington, DE
    Posts
    6,207

    Default To all the diode nuts...

    I'm at a bit of a loss here. I've tried searching PL and looked through a lot of threads but, is there some sort of tutorial floating around for the basic testing a diode. What to do, what not to do, etc.

    Aside from some basic knowledge, I'm fairly ignorant about diodes compared to most people around here and, I guess there is more of a wealth of knowledge at the laser pointer forum but, for one thing, the damn things are too tiny for me to mess with. I'm near sighted and wear contacts but, when they're in, looking at things up close has become a chore and I know I need to get a decent, lighted magnifying glass one of these days.

    Anyway, I bought a lumia projector from Stuka at SELEM this year which is a mixture of an argon and then two diodes in Maxyz modules. One is a red, the other was a 405nm violet. I have no idea what the power of it is supposed to be but, just before selling it to me at SELEM, the 405 kinda went LED I guess. It glows purple but doesn't lase. So... shortly after SELEM, I picked up a 100mW 405nm in an Aixiz mount with leads from rfourt in a sale on here to replace it. Today, I ventured into trying to fix it and when holding the leads for the new 405 to the leads from the driver, I get nothing. Reverse them... nothing. So, two things come to mind - either the new 405 doesn't work or, the driver isn't putting out enough current to cross the threshold of making it light. I'm guessing maybe the latter as it was sold to me as "fully functioning". But, question one is this:

    Can one just take a bench top power supply or even a battery of some sort and apply a little power to a diode to check it if works or, even for a quick color identification. Or, do you need a driver of some sort? 'Cause I don't know shit about them yet either. Got a box full of flexmods and a few from Badpip when the time comes to learn though! I'd like to confirm this new 405 from rfourt actually works before pressing it out of the aixiz mount and trying to put it into the Maxyz module and begin messing with the rediculously tiny screws I found on this driver.

    I also got a bag with some loose diodes taken out of (I guess) DVD burners or Blue Ray players from rfourt as well. And, all the diodes I've seen and have been referenced on here have three leads (in the upside down V shape). I know they're not standardized but that in most cases positive is normally the one on the left and the center is negative but, a lot of these diodes have 4 leads. (???) I got nuttin'. Can't even hazard a guess.

    So, is there a good reference or tutorial anywhere someone can suggest that I can read up on a little more?

  2. #2
    Join Date
    Dec 2009
    Location
    London UK
    Posts
    224

    Default

    The most common Violet diode is the PHR 803T, the pinout for that looking at the upside down 'V' is right-Positive, Left-Negative/Ground.
    The Violet diode needs 4.5 volts to lase. We used to set the current at 110ma

    For testing diodes you can build a quick LM317 driver and use a 1ohm resistor & multimeter to set the output it. Info here http://www.rog8811.com/laserdriver.htm

    Hope this helps?

  3. #3
    Bradfo69's Avatar
    Bradfo69 is offline Pending BST Forum Purchases: $47,127,283.53
    Join Date
    Jul 2010
    Location
    Wilmington, DE
    Posts
    6,207

    Default

    Thank you. That is a helpful article and a good start.

  4. #4
    Join Date
    Feb 2011
    Location
    St. Louis
    Posts
    526

    Default

    I see where you said you were holding the driver leads to the diode leads. I would highly suggest a solid connection preferably soldered between the diode and driver where there is not a chance of intermittent contact while the driver is powered which could charge up the output cap and then discharge a surge into your diode killing it.

  5. #5
    Join Date
    Aug 2008
    Location
    Berkshire
    Posts
    664

    Default

    Hey Brad
    Odicforce sell a diode and LED tester:
    http://www.odicforce.com/shop/articl...aid%3DOFL61%26

    cheers
    Adrian

  6. #6
    Join Date
    Jul 2007
    Location
    Knoxville, TN, USA
    Posts
    3,154

    Default

    Ping DZ about the replacement, specs, etc. -

    He's the original builder, and can probably guide you on recommendations for a replacement diode...
    RR

    Metrologic HeNe 3.3mw Modulated laser, 2 Radio Shack motors, and a broken mirror.
    1979.
    Sweet.....

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •