Page 2 of 2 FirstFirst 12
Results 11 to 15 of 15

Thread: Help with Mitsubishi Quad setup

  1. #11
    Join Date
    Feb 2011
    Location
    New Hampshire
    Posts
    3,513

    Default

    With any diode output that is asymmetrical (a stripe) you can stack (vertically) or knife edge (horizontally) and so yes I could have done that. But, Dave is correct. With a vertical stack the cylinders can be positioned in the horizontal plane with enough precision by sliding them from side to side by hand as they sit on the deck. This would be much harder to do up and down against a vertical wall fighting their tendency to fall down if the retaining screw is just a little too loose.

  2. #12
    Join Date
    Jul 2007
    Location
    Slovakia Europe
    Posts
    24

    Default

    hi planters,

    maybe dumb (newbie) question, just trying to understand ...

    if cylinders are positioned on horizontal plane then they are expanding the beam horizontaly. right ?
    if two beams are to be combined they should be (as you wrote) verticaly stacked.
    like this ? (every beam at different height)
    |
    |
    why not knife edged like this ?
    ||

  3. #13
    Join Date
    Jul 2007
    Location
    west sussex uk
    Posts
    2,280

    Default

    The beams have to be
    Stacked on top of each orher because both beams have to be dead center
    To the cylinder lens , stacking next to each other wont allow this to happen
    Also using the 2mm fl lens would allow a tripple stack
    Through one lens set making a six banger possible
    But you would need big mirror galvos to make full use of the beam



    Quote Originally Posted by pishtak View Post
    hi planters,

    maybe dumb (newbie) question, just trying to understand ...

    if cylinders are positioned on horizontal plane then they are expanding the beam horizontaly. right ?
    if two beams are to be combined they should be (as you wrote) verticaly stacked.
    like this ? (every beam at different height)
    |
    |
    why not knife edged like this ?
    ||
    When God said “Let there be light” he surely must have meant perfectly coherent light.

  4. #14
    Join Date
    Feb 2011
    Location
    New Hampshire
    Posts
    3,513

    Default

    What badger said is correct. You should also understand what is actually happening when you use the cylinders to expand the beam. The far field divergence decreases proportionally as you expand the beam in the near field. There is no free lunch and so if you want the lowest far field divergence possible then you want to expand in the near field as much as your scanners will allow. In addition to the optical aberrations caused by operating off axis as was stated by badger the side by side stacking will give you at the best a beam that is twice as wide to start and then the ratio of available expansion will be cut in half and the far field divergence will double (and furthermore, you'll never actually achieve 100% packing efficiency anyway).

    Also, the most efficient use of a scanner is when the mirrors are completely filled , but without spilling over the edges. This usually will require a near square shaped beam and so this should be your goal when you are done with your beam manipulations. You can see that "ll" when expanded will be an a squat rectangle and will leave a large part of the scanner mirror empty.

  5. #15
    Join Date
    Feb 2013
    Location
    Toronto, Canada
    Posts
    33

    Default

    Good-day,

    I will also be attempting this in the near future. Are there any videos that explain this topic?

    Thanks!



    Quote Originally Posted by planters View Post
    What badger said is correct. You should also understand what is actually happening when you use the cylinders to expand the beam. The far field divergence decreases proportionally as you expand the beam in the near field. There is no free lunch and so if you want the lowest far field divergence possible then you want to expand in the near field as much as your scanners will allow. In addition to the optical aberrations caused by operating off axis as was stated by badger the side by side stacking will give you at the best a beam that is twice as wide to start and then the ratio of available expansion will be cut in half and the far field divergence will double (and furthermore, you'll never actually achieve 100% packing efficiency anyway).

    Also, the most efficient use of a scanner is when the mirrors are completely filled , but without spilling over the edges. This usually will require a near square shaped beam and so this should be your goal when you are done with your beam manipulations. You can see that "ll" when expanded will be an a squat rectangle and will leave a large part of the scanner mirror empty.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •