Page 2 of 2 FirstFirst 12
Results 11 to 15 of 15

Thread: Mobolazer ML10- 250 Help

  1. #11
    Join Date
    Dec 2006
    Location
    denver,co
    Posts
    1,078

    Default

    Barbizon will have any of the dmx cables you need. It looks like 5 pin for the mobo and nsi controller and three pin for the remote.
    http://www.barbizon.com/store.php?cPath=293_25

    chad


    When the going gets weird, the weird turn pro.


  2. #12
    Join Date
    Mar 2013
    Location
    Colorado
    Posts
    6

    Default

    okay finaly got all the cable fired it up , didnt see anything until i took the plastic plugs out rectangular box on side. i think dmx isnt working properly OR dipswitch settings are wrong. All dipswitches are up, please let me know from here when you get time. I am coming to Denver on 4/19 and 4/20 to sporting goods convention also thanks again Kelly

  3. #13
    Join Date
    Mar 2013
    Location
    Colorado
    Posts
    6

    Default

    Ok so here is whats happening, The dmx has no effect at all on the mobo. However when I plug the keyswitch in ancd turn it on , after a minute or so the laser fires up in blue, but just inside the side box. nothing out the tourrets? Kelly

  4. #14
    Join Date
    Sep 2007
    Location
    Texas
    Posts
    807

    Default

    Quote Originally Posted by kellythomasmiguel View Post
    Ok so here is whats happening, The dmx has no effect at all on the mobo. However when I plug the keyswitch in ancd turn it on , after a minute or so the laser fires up in blue, but just inside the side box. nothing out the tourrets? Kelly
    Blue light in the enclosure is a good sign, at least the laser appears to still function. There may be a beam shutter that is terminating the beam (Brad or Frank can confirm this). A beam table uses pick-off mirrors to direct the beam up into the turrets, so you won't see anything until the DMX is working and is deflecting the beams. I'd say so far, so good - I would think that something on the DMX configurarion may be set wrong.

    Greg
    "Information not shared, is information lost forever"

    Join ILDA
    Support Photonlexicon

  5. #15
    Join Date
    Jan 2006
    Location
    Charleston, SC
    Posts
    2,147,489,632

    Default

    Quote Originally Posted by Displaser View Post
    Blue light in the enclosure is a good sign, at least the laser appears to still function.
    Agreed. At least his laser is good. Now he just needs to get DMX working and he's off to the races...
    There may be a beam shutter that is terminating the beam
    There is definitely a beam shutter that blocks the beam from entering the rest of the rail. If that actuator isn't energized, you won't get any light. He can pull the front plate off and see this, but I wouldn't suggest it just yet, especially if he doesn't have any safety goggles. Some of those Reliant's can make north of a watt, which could make for a nasty surprise!
    A beam table uses pick-off mirrors to direct the beam up into the turrets, so you won't see anything until the DMX is working and is deflecting the beams.
    There is also the alignment of the laser to the rail... That can get knocked out of alignment if the unit was bounced around a good bit. Mobolasers use a series of pinholes to get the alignment right.

    But yeah, he needs to get the DMX working first. Then, when he hits the buttons on the DMX control panel, he should be able to hear the actuators firing inside the Mobo. If that's working, and he has the shutter open, and still no light, THEN he should pull the front panel off and try aligning the beam to the rail. (But be mindful of the danger of taking a shot to the eye from that Reliant, which will be running at full-tilt.)
    I would think that something on the DMX configurarion may be set wrong.
    Agreed. He probably just needs to set the DMX address correctly. Worst case, the board itself may be fried, but that's unlikely.

    Adam

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •