Page 1 of 5 12345 LastLast
Results 1 to 10 of 42

Thread: 6watt 445 Build

  1. #1
    Join Date
    Dec 2006
    Location
    Essex, UK
    Posts
    8,647

    Default 6watt 445 Build

    an 8 diode 445 ive been working on



    Eat Sleep Lase Repeat

  2. #2
    Join Date
    Feb 2011
    Location
    New Hampshire
    Posts
    3,513

    Default

    Nice machining, but only 6W?

  3. #3
    Join Date
    Feb 2008
    Location
    East Sussex, England
    Posts
    5,248

    Default

    That was my query on Facebook.
    With the right diodes you could get at least 9W out of 6 diodes before optics.
    Frikkin Lasers
    http://www.frikkinlasers.co.uk

    You are using Bonetti's defense against me, ah?

    I thought it fitting, considering the rocky terrain.

  4. #4
    Join Date
    Dec 2006
    Location
    Essex, UK
    Posts
    8,647

    Default

    cos i dont over drive the diodes

    they are set to around 1.1w each and after knife edging and optics you get 6watts out.

    im sure people coiuld do the same setup and turn the diodes up but its just not what i do
    Eat Sleep Lase Repeat

  5. #5
    Join Date
    Aug 2010
    Location
    Belgium
    Posts
    295

    Default

    Maybe there is a missing "1" before the "6"W ?!

    16W could be achievable with 9mm diodes. But in this case, heat generated is greater than 80W, big big tec under the module should be envisaged. Or you plan to do passive --fan-- cooling?

    --- www.neodym.be ---

  6. #6
    Join Date
    Apr 2010
    Location
    Grand Rapids, Mi
    Posts
    2,538

    Default

    Quote Originally Posted by andy_con View Post

    im sure people coiuld do the same setup and turn the diodes up

    -> points finger at self.

    Great build, Been using your (surplus) mounts you sold in some recent build, the diodes end up amazingly centered as compared to other I have used.
    leading in trailing technology

  7. #7
    Join Date
    Dec 2006
    Location
    Essex, UK
    Posts
    8,647

    Default

    glad your happy with them

    9mm diodes are only rated at 1.4w each so x 8 = 11.2w without any losses
    Eat Sleep Lase Repeat

  8. #8
    Join Date
    Aug 2010
    Location
    Belgium
    Posts
    295

    Default

    Ok, explanation arrived before I send the message

    --- www.neodym.be ---

  9. #9
    Join Date
    Feb 2008
    Location
    East Sussex, England
    Posts
    5,248

    Default

    cos i dont over drive the diodes
    Nor do some other folks. I believe the ~1.8W single diode modules Mr Briggs was/is selling are run at normal current. He's just graded the diodes I think.

    Do you set the modules up by current or by power output? If its by power then you could actually be overdriving some of the diodes (as far as your definition of overdriving is concerned)
    Frikkin Lasers
    http://www.frikkinlasers.co.uk

    You are using Bonetti's defense against me, ah?

    I thought it fitting, considering the rocky terrain.

  10. #10
    Join Date
    Feb 2011
    Location
    New Hampshire
    Posts
    3,513

    Default

    Although I see the point in conservative operation of a diode, there is a balance. I am not talking about the additional initial cost of the additional components because this might avoid the costs/hassles with diode replacement. Rather, if the diodes were operated at say1.5W each then the 6W beam could fit on a smaller scanner or the same scanner wold allow 1/2 the beam divergence.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •