Page 4 of 5 FirstFirst 12345 LastLast
Results 31 to 40 of 42

Thread: 6watt 445 Build

  1. #31
    Join Date
    Feb 2011
    Location
    New Hampshire
    Posts
    3,513

    Default

    White-light,

    With that avatar, anything you say will require a lot of back up documentation. Nevertheless, these modules are optically very straight forward. If they are well designed, the replacement of a diode shouldn't require a high level of skill or experience. The same goes for the alignment of the diodes/modules. The RARE replacement or adjustment, if it allowed double the power output of a given laser, seams like a reasonable trade off.

  2. #32
    Join Date
    Feb 2005
    Location
    Switzerland
    Posts
    1,411

    Default

    Mmmm, the failure specifications says that after 20'000 hours at 1.2A, only 63% of the diodes will have >50% of the initial power. So 37% will have less than half, even no output at all.
    That means there is a constant degradation of the output power, and it should be way faster with 1.7A (as an absolute max rating which should be avoided) instead of the 1.2A from the spec.
    So within spec current I assume they will be good for >5000 hours without any power loss, but at 1.7A it could fall to only a few hundreds hours, especially when not cooled correctly.

    You'd better find some "rank D" group of diodes, coupled with a longer wavelength, rather than driving them at absolute max rating Then you could keep your hardly earned money to buy new equipment rather than servicing your existing one...

  3. #33
    Join Date
    Dec 2006
    Location
    denver,co
    Posts
    1,078

    Default

    I wonder about all of this. The Ca$$ios run them hot. Like at their max of 50c. They run for a two thirds duty cycle. And ca$$io warranties them for lots of hours.
    They might be down a little in power but they are not going to be half of the brightness. Laser show duty is much easier on them then the vid proj. I have no qualms with running them at 1.7 maybe 2.
    However good thermal is important.

    chad


    When the going gets weird, the weird turn pro.


  4. #34
    Join Date
    Jun 2010
    Location
    Australia
    Posts
    3,733

    Default

    Nice one Andy !

    Looks like you have the mill fully sussed.

    I am with you about not over driving the laser diodes. Lost too many during shows to ever want that happening again...
    This space for rent.

  5. #35
    Join Date
    Aug 2008
    Location
    UK
    Posts
    5,704

    Default

    Quote Originally Posted by planters View Post
    White-light,

    With that avatar, anything you say will require a lot of back up documentation.
    If you mean the signature, its a joke coming from another thread. I'm not called Alan..... (altered now to avoid confusion).

    I readily admit i know little about building.

    Quote Originally Posted by planters View Post
    Nevertheless, these modules are optically very straight forward. If they are well designed, the replacement of a diode shouldn't require a high level of skill or experience. The same goes for the alignment of the diodes/modules. The RARE replacement or adjustment, if it allowed double the power output of a given laser, seams like a reasonable trade off.
    I'm not denying that and its all opinion. But there are a lot of people out there who eg can't wire a plug. The way I look at this from Andy's sales point of view (bearing in mind he sells elsewhere than on here) is who is Joe Average and what does he want? Is he going to be the bloke who can take apart and repair a module like many capable people on here, or is he going to the type of bloke who'd rather leave that to someone else? If the latter, what's more important ultimate lifetime or a little extra power? It's all opinion but again to a non professional, repairs are expensive so I'd personally regard lifetime as more important than power, but then again that's only my opinion.

    I also think Chad has a very good point, from memory you have to triple the power to double the brightness. So if Andy squeezed a few hundred mw from the diode would it even be noticeable? It might be if you were under powered in that colour and looking for a little more to achieve white balance although then the argument goes you could easily balance that in the software which whilst resulting in a slight reduction in power in the other colours, would that reduction even be noticeable?

    I don't know it all a matter of opinion - ultimate lifetime vs power, horse for courses and I guess what Andy feels happiest doing.
    Last edited by White-Light; 05-16-2013 at 02:17.

  6. #36
    Join Date
    Dec 2006
    Location
    Essex, UK
    Posts
    8,647

    Default

    Nice one Andy !

    Looks like you have the mill fully sussed.

    I am with you about not over driving the laser diodes. Lost too many during shows to ever want that happening again...

    thanks, people still seem to be obssessed with power power power. whereas theres more to lasers than just power.

    as these modules are not for me but for customers i want them ot last long and not go wrong.
    Eat Sleep Lase Repeat

  7. #37
    Join Date
    Feb 2011
    Location
    New Hampshire
    Posts
    3,513

    Default

    This is all a friendly back and forth about philosophy. There is no wrong or right...obviously. Andy, the quality of your module based on the aesthetics (it's beautiful), and the neat and efficient lay out is very good. Your logic regarding the current setting for your diodes is sound even if I personally disagree with your assumptions about the relative value of lifetime vs power output.

    White-light,
    The market for these lasers is not clear to me. With all the concern about safety frequently discussed on this forum, if the end user of a projector where just one of the three laser modules conservatively generates 6W of well colimnated power does not have a moderate level of competence with electronics and optics then that's scarey. Remember, this is just a module. It will have to be powered, co-aligned and fed to a scanner with interlocks (if used). The projector will have to be encased, cooled, switched and linked with DB-25 or ether net etc.

    I believe that much of the continuing excitement about these display laser systems comes from the incremental increases in power, beam quality(lower divergence/scatter), scanner speeds and available colors. Some people are constantly pushing the limits and others are following a step or two behind in order to benefit from a more conservative approach. Those benefits include less engineering cost/time and lower rates of component failure. But, both groups are moving forward. 3 years ago a 6 W module would have been jaw dropping.

  8. #38
    Join Date
    Sep 2012
    Location
    Sweden
    Posts
    14

    Default

    Have seen some of your builds over the last year or so from time to time at LPF. They are just getting cleaner and cleaner. Really like the “solid” 90 degree kvant looking (sort of) mirror mounts minus the prisms. Where did you get them? Did not see a waveplate in there? You running the beens at 90 degrees? If so how does the beam look at distance? I am guessing you are using o-likes lenses?

    Seriously your stuff looks like art! Definitely an inspiration.
    gpg --keyserver pgp.mit.edu --recv-keys 0x2B4B58FE
    BTC: 1onryo1uHwq8gkj6bM3iKMhxuHTde18JG

  9. #39
    Join Date
    Dec 2006
    Location
    Essex, UK
    Posts
    8,647

    Default

    Quote Originally Posted by onryo View Post
    Have seen some of your builds over the last year or so from time to time at LPF. They are just getting cleaner and cleaner. Really like the “solid” 90 degree kvant looking (sort of) mirror mounts minus the prisms. Where did you get them? Did not see a waveplate in there? You running the beens at 90 degrees? If so how does the beam look at distance? I am guessing you are using o-likes lenses?

    Seriously your stuff looks like art! Definitely an inspiration.
    every bit of metal in that module i machined, so made the mirror mounts.

    waveplate is glued to the front of the PBS
    Eat Sleep Lase Repeat

  10. #40
    Join Date
    Dec 2006
    Location
    Essex, UK
    Posts
    8,647

    Default

    6w and 3.6w next to each other



    Eat Sleep Lase Repeat

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •