Page 4 of 4 FirstFirst 1234
Results 31 to 34 of 34

Thread: Buying first RGB laser

  1. #31
    Join Date
    Jun 2013
    Location
    Sydney, Australia
    Posts
    244

    Default

    I did wonder that Karl, but the CPU meter was only around 10% most of the time, it is an I5 laptop with 8gb Ram. I have also tried a touchscreen desktop machine with core 2 duo and 2gb Ram (I know there are other factors) but neither seemed to struggle?

    I do have an Easylase DAC, but no software to try with that?


    Quote Originally Posted by WookieBoy View Post
    Hi Steve.

    Ummm... if QS is showing a low FPS number it could be that your control computer is struggling to process things quickly enough... I think.
    I get similar flikering when running QS with other stuff open in the background, but usually only when running both my FB3 as seperate images.
    I may be waayy off here, but try closing all other programs and background running aps like the funky Windows Desktop etc and see if that helps?
    At the very least it'll rule out a factor...

  2. #32
    Join Date
    May 2008
    Location
    Once it was called "Bel Paese" = ITALY
    Posts
    858

    Default

    Quote Originally Posted by steviobee View Post
    Thanks Steve, will try this as well, does yours flicker at these settings, I will use the 'Top' test image square? Mine seems to always flicker whatever size I have it at?
    Gosh!
    If I use QS "Top" test image at low scanspeed.... I think surely it will be flicker.... (honestly I never tested before...)
    As you know, this means that you have to reduce scan angle and/or increase scanspeed...

    Well...
    The most important thing you have to obtain is: the exact match between emission angle and "X-Y" rate settings of QuickShow.
    Firstly you will be sure that, setting 100% of X-Y size, you obtain the exact corresponding size projected measured for that specific angle of projection. Then you can start to do all test needed. Not before ot this, because it would be a "non sense" or a "fake" test.
    I have set all my four RGB projectors this way and everything works fine.

    I'm sure you will have not any flickering issue when at the right emission angle and at the right scanspeed.
    Your DT40 pro are good scanners! (surely much better than my Laserworld 50K....)
    my webpage
    http://stevemilani.jimdo.com
    Skype ID: stevemilani957

    my RGB analogue projectors:
    3.9 W (640/532/445) 30kpps
    2.6 W (655/532/450) 30kpps
    2.5 W (638/532/450) 30kpps
    0.7 W (test unit)(635/532/473) 18kpps

  3. #33
    Join Date
    Feb 2008
    Location
    East Sussex, England
    Posts
    5,248

    Default

    I've just read back to the last page, and it sounds to be like you are simply trying to display cues at full angle that were never designed to be. This is a sure fire way to kill your scanners.

    So, before you go any further, consider this.

    You should be able to scan 'beam' effects (flat planes, circles, etc) at full angle.
    Things like clocks, animations, etc are designed to be projected onto specific targets, scrims, screens, etc and so the graphics zone will be adjusted down to the correct size for the target.

    Go to Settings-->Projection Zones-->Main Graphics-->Geometric Correction and set the size to 30 on each axis and then try again. You should now get much smoother frames and a lot less noise on the scanners.

    The ILDA test pattern is 30k at 8 degrees, you can use this as a good rule of thumb for size when projecting relatively complex graphics if you want to hit 30k scan speed.
    Frikkin Lasers
    http://www.frikkinlasers.co.uk

    You are using Bonetti's defense against me, ah?

    I thought it fitting, considering the rocky terrain.

  4. #34
    Join Date
    Aug 2008
    Location
    UK
    Posts
    5,704

    Default

    Download Tim's utility as it will probably help you:

    http://www.photonlexicon.com/forums/...gle-Calculator

    Enter 8 degrees and the distance to the wallfrom your prjector in inches and it will then tell you the square (side) size.

    EDIT: Download the updated version in post #7 and you can use centimetres instead of inches.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •