Small Sunon Maglev ('vapo' bearings) aren't that quiet. They ought to be, but I found that resonances in the blades make more noise than is silenced by the bearings. I went for a Papst ball-bearing fan chosen specifically for low noise, and got better results. Broadband noise is far easier on the ear than narrowband resonant whine, so don't judge by the noise figures alone, they don't tell what sort of noise you'll get.
One trick I intend to try in the near future is to get a 12V fan rated for high output, and run it on 5V (or 7V as supplied across yellow and red wires in a standard computer power supply, but only do that if you aren't using a tachometer or other third wire function.) As it is a higher power fan, the current should be enough that it starts and runs well on lower volts. It will run cooler, and last longer. It will be much quieter. There will usually be a fan made for similar ability at standard voltage, but this trick might save you money. It's usually cheaper to adapt a widely used common standard than to buy a fan that meets a more rarely demanded spec. It also drops the risk of exciting unpleasant resonances so is especially useful to fix what may be the most annoying problem.
Ok. And at 14dB they should be too. I was going by the few Sunon fans I had, and the entire Sunon catalog PDF as stored by RS Components. They don't have a V4 in that one, ranges from VX,V1,V2,V3. VX is especially noisy, resonance in the blades makes a large whine that vapo bearings do nothing to help with. There are fans with louder noise figures that sound far less offensive. I think Sunon must have answered calls for real silence.
Back from the dead! I've got some new PJ's for my studio and they're unbearably loud. The design is a single level with the modules, scanner and scan amps sitting on an elevated heatsink. The heatsink fins are aligned so that air can be drawn through their channels and expelled via some very loud fans. The supplies in the box are +/- 24 for the scanners and 12V for everything else. The fans are 2-wire DC running at 12V also. Not knowing much about electronics, but being handy with a soldering iron, what are my options for slowing these suckers down?
What I don't want to do is:
1. Replace the fans
2. Replace the PS (with a 12/5 for instance).
I'm looking to drop the voltage to the fans to 6 or 7V each yet still allow 12V to the rest of the components in the case. Should I just build a voltage dividing circuit with a pair of resistors in series across the +/Gnd leads and tap from the center of it for my fan + lead? will this have any adverse affect on the rest of the electronics or power supply?
Thanks in advance,
-rick
Use a variable DC-DC converter. Banggood do a tiny one good for driving fans for a few $$
In fact, you can buy 20 pcs for less than a tenner! Wide input and output ranges, up to 3A output. I've got at least one in most of my projectors these days...
http://www.banggood.com/20Pcs-Mini-D...-p-951167.html
My latest 3W projector builds have the scanner PSU and a single 6V PSU for the whole lot (using one of these step down to provide 5V for the electronics, safety, etc boards)
Frikkin Lasers
http://www.frikkinlasers.co.uk
You are using Bonetti's defense against me, ah?
I thought it fitting, considering the rocky terrain.
I use Arduino to control the fan using PID algorithm ,
fans are running at 20% most of the time, and climbs when its out of its setpoint,
I believe DTR has got lots of 60mm x60mm fan that are quite iirc
Philipp Wetter
Norty,
thanks mucho, those look just the ticket. Phillip, I'm sure arduino would do it, but the last thing I need is another hobby. I'm playing a zero sum game here and would need to chuck one of my other hobbies first![]()
Have a lottle browse of their electronic boards section before you check out, they do a load of handy little ones for tuppence ha'penny that you might want to order all in one go.
I've got a load of odds and sods here just waiting for a purpose![]()
Frikkin Lasers
http://www.frikkinlasers.co.uk
You are using Bonetti's defense against me, ah?
I thought it fitting, considering the rocky terrain.