Results 1 to 8 of 8

Thread: Tarm Vision Bank 5W

  1. #1
    Join Date
    Sep 2012
    Location
    Hannover, Germany Formerly Spartanburg, S.C.
    Posts
    20

    Question Tarm Vision Bank 5W

    Hi all,

    Im currently setting up/purchasing a lighting setup for a club in Germany and Im currently looking at a Tarm Vision laser bank. Its a Gas monster with a spectra physics Chroma 5 light source. According to seller the unit has around 960hrs on it. Age circa 1997. I love the Tarm beamtables because of all the output capabilites and effects. This particular bank has 2 sets of 60K scanners and a fiber output running to 2 satellites with 30k scanners. Plus the usual effects like grating, line grate, star effect, etc. etc. The whole unit is complete with touchscreen PC and LD2000 software. Asking price is €6000.

    Couple of questions.

    1. Is it worth going the gas route? I have seen plenty of gas lasers especially in the Tarm bank setups and absolutely love the beam characteristics and colors. Have never seen a diode setup put out colors like that. But is it worth the hassle of liquid cooling and the cost of the power consumption? Power here is up to an absurd 39C per Kwh.

    2. Is the age and runtime of the laser something to worry about? Possible gas fill?

    3. If its not worth running the gas module, is it possible to run the tarm bank and just replace the Chroma 5 with a 6W RGB diode from Tarm or Kvant?

    4. What all would be involved in replacing the Gas with a diode? I assume it isnt just plug and play.

    What are your thoughts in General on the this setup as far as features and price? The club this is going into is a smaller club, around 1000Sq M. Low ceiling height of 3M.

    Is worth it or should I be looking into a smaller diode system like a Kvant spektrum? (which would end up being the same price)

    Thanks,

    Steven

  2. #2
    Join Date
    Sep 2012
    Location
    Hannover, Germany Formerly Spartanburg, S.C.
    Posts
    20

    Default

    Oh, almost forgot.

    The laser currently needs a fresh water hookup for cooling. Is it possible to convert the cooling system to closed loop with a reservoir and a radiator?
    What type of cooling capacity to I need to figure with? maximum power consumption is 25KW.
    What temperatures need to be maintained?

    Steven

  3. #3
    Join Date
    Jun 2012
    Location
    Bree North West, Middle-Earth
    Posts
    298

    Default

    Steven,

    Is this the unit you are looking at?

    http://laserlikers.net/laser_marktpl...erent_star_ii/

    I think the price is much lower here?

    Cheers

    Steve

  4. #4
    Join Date
    Sep 2012
    Location
    Hannover, Germany Formerly Spartanburg, S.C.
    Posts
    20

    Default

    Similar, The one Im looking at is a bit bigger. Very few pics of it on the net. Was the standard install system here in clubs in the 90´s. Here is a link to the listing, dont know why I didnt post it earlier.

    http://www.gebrauchte-veranstaltungs...how-programmen

    Here is a video of the twin scan system with satellites in action

    http://youtu.be/qyx1k31Q4y0?t=1m12s
    Last edited by steven850; 08-31-2013 at 04:22. Reason: Additonal Link

  5. #5
    Join Date
    Oct 2008
    Location
    Portland
    Posts
    1,566

    Default

    Gas will look better but I am an ion guy... There are facilities in Germany to get it regassed (mixedgas should hopefully chime on that department). The other thing is you can still use the beam table for solid state lasers later. Wait for other replies as I am biased.

    -Adam
    Support your local Janitor- not solicited .

    Laser (the acronym derived from Light Amplification by Stimulated Emissions of Radiation) is a spectacular manifestation of this process. It is a source which emits a kind of light of unrivaled purity and intensity not found in any of the previously known sources of radiation. - Lasers & Non-Linear Optics, B.B. Laud.

  6. #6
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    The Laser never draws the full 25 KW. However 1 Kilowatt is 3,500 BTU per hour and you can run it off a water to air exchanger if you have a place to dump the heat to. The usual way we economize is a water to water heat exchanger. It only draws water when its reservoir temperature exceeds its setpoint. Most clubs do not run the laser at full power nor do they run it all night, so the w2w system is economic. It reduces the bad habit of dumping 2.5 GPM or more down a drain when its heat capacity is not effectively used. The laser is more stable as well.

    If you placed a pair of 55 gallon drums of water in series with the laser, and allowed it to cool to room temperature using a radiator when the club was closed, it would be 1.5 to 2 hours before your water to water exchanger even kicked on. Compared to the soda machines,ice machines, and women's toilets in a decent sized club, the laser, done properly, is small potato's.

    The Chroma series has a closed loop, automated, gas refill system, there are no cartridges.
    This system lasts a long, long time. At the end of that time the tube can be rebuilt once.

    I wont comment on scrapping the Chroma, I'd need to test the plasma tube to comment about that. YES, you could retrofit with solid state, loosing the yellow, violet and some of the extra blues and greens an ion system provides. However, without running it, there is no way to measure the status of the Chroma, it might have 2500 hours to 3500 to 5000 hours left in it. On the other hand it may be shot.

    By German standards a professional club show without a beam table, gratings, and a remote head or two sucks.


    I know of two good companies in Germany that still support that laser. My initial call would to be evaluate Chroma, buy Das Wonderlich Projector, and then retrofit to solid state Green if the gas laser is a loss. You will however need a exceptional green beam quality to drive the fibers.

    YOU HAVE A UNIQUE LASER REGULATORY SYSTEM IN GERMANY, your install needs to be inspected. Ask for details at Laserfreak.de

    6000 is way too much for that system.

    Steve
    Last edited by mixedgas; 08-31-2013 at 13:34.
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

  7. #7
    Join Date
    Sep 2012
    Location
    Hannover, Germany Formerly Spartanburg, S.C.
    Posts
    20

    Default

    By German standards a professional club show without a beam table, gratings, and a remote head or two sucks.
    Agreed, thats why im looking to these systems.

    I know of two good companies in Germany that still support that laser. My initial call would to be evaluate Chroma, buy Das Wonderlich Projector, and then retrofit to solid state Green if the gas laser is a loss. You will however need a exceptional green beam quality to drive the fibers.
    Green only? I would definitely want to have RGB in this system.

    YOU HAVE A UNIQUE LASER REGULATORY SYSTEM IN GERMANY, your install needs to be inspected. Ask for details at Laserfreak.de
    I am aware of the steps required here in Germany, I have a German laser certification. Ive just never messed with any of the gas systems.

    6000 is way too much for that system.
    What do you think its worth? TARM has one one their website without Satellites, and only one set of scanners for 10,000. So the 6K sounded good to me.

    http://www.tarm.com/index.php?id=96&L=1

  8. #8
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    I don't know what your budget is. Getting RGB into tight fibers requires better then average solid state lasers. Gas lasers excelled at small, high grade, TEm00 beams. Depending on the fiber core size, it may be very difficult to do without switching to much larger fiber cores, then the traditional 62/125 fibers. Possible candidate red lasers for driving fiber heads are still very expensive at this point. Green candidate lasers are far more plentiful. Blue would be a 473 nm or 458 nm blue, or just a few 445 nm diodes.

    My guess is that a very high spec Chroma is worth 1500$ to 2500$ at this point to a Club that can use it. Unless all of the scanners in the system are Cambridges, the rest of the system is not worth much, save for the Pangolin. Except for one thing, It can do what you want, better then most modern hardware.

    So if you need RGB, you may be better off with stock Kvant or RGB Systems units, unless a professional can match lasers to the fibers for you.

    It is a tough call, and again, without running the Ion laser and/or talking to its previous owner, the upgrade path using OPSL or similar for red may be cost prohibitive. If you can abandon the fiber heads, use larger fiber, or have green only remote heads, then solid state upgrade is an option.

    Is it cost effective for you to upgrade? , Will it last any length of time? , is difficult to quantify.


    The equivalent Coherent lasers, which were very common in Europe, are Purelight Star or Star II. If you buy the system and find a working, Star as a backup, you may be very, very happy.

    What does it offer:

    A nice control system. (How many Pangolin Quadmods does it come with?)
    A beam table that can be repaired if needed and upgraded to modern gratings, inexpensively. (How many beam positions does it have?)
    Regulatory approval for the hardware is in place.
    Remote Heads.
    A manual console.
    Fiber heads that can be easily moved.

    What might be better?

    6000 Euros gets you a lot of solid state.

    What is the tradeoff?

    Limited Laser Lifetime, a few years at best, replacement cost, and operating cost vs Kick A$$ show, Easy Regulatory approval, and wow factor.

    See if RGB or Kvant offer a beam table, and decide accordingly.

    So how much does Cambridge Laser Labs, HB laser, or Dirk in Germany want to keep you in bathed in Ion Laser Photons?

    It just Might not be cost effective. On the other hand, German, Approved, laser gear is far more expensive then Asian or US used gear.




    Steve
    Last edited by mixedgas; 09-02-2013 at 18:48.
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •