Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 33

Thread: Reliable and consistent laser diodes?

  1. #21
    Join Date
    Nov 2008
    Location
    Cleveland Ohio
    Posts
    2,613

    Default

    25-75k for opsl

  2. #22
    Join Date
    Jan 2007
    Location
    Florida
    Posts
    4,382

    Default

    Quote Originally Posted by kecked View Post
    25-75k for opsl
    Yeah, and looking inside one doesn't look like it's worth quite all that. I imagine most of the cost rests the in the design?

  3. #23
    Join Date
    Mar 2006
    Posts
    2,478

    Default

    Ok, I am now recovered. I think the whole of PL hit the floor last night, quite the down time.. (Although I guess that was Spec doing some deep cleaning, I'm not sure that forum software has pockets to hit or jaws to drop). Anyway, no OPSL for me. Slightly off-topic but maybe interesting, those projectors with the lasers and MEMS mirrors... I don't know what the pixel size is but it seems to me that if you don't have to focus, and if the pixel size is small enough, then one of those might be like having tens or hundreds of tiny laser projectors all pointing together out of a small window. What they would lack in power, being made to look like actual scanned-beam displays, they might make up for in weight of apparent numbers, especially for wide projections that would otherwise spread the power of a scanned beam thinly. Though whether they'll ever look as sharp and lively as the specular light of a scanned beam is in doubt.

  4. #24
    Join Date
    Mar 2006
    Posts
    2,478

    Default

    Another question...
    (Old as the hills around here, but still maybe not resolved, so I'm interested in any point of view about this.)

    If a multimode diode with narrow 'stripe width' is so fine in the 'slow' axis that it can focus like a single mode diode, is it reasonable to expect the 'fast' axis to be correctable after the same lens by using anamorphic prisms, getting a better result than 'knife-edging' three collimated single mode diodes such that their beams are parallel and in same plane?

    To put that another way: Is there some nasty habit of divergence in the multi-mode axis that prevents a fine result from the diode even after the prisms have had a go at it?

  5. #25
    Join Date
    Feb 2008
    Location
    Northern Indiana
    Posts
    921

    Default

    The "narrow stripe width" is the fast axis. The slow axis is the wider part of the facet. The limiting factor achieving a low divergence beam with small diameter is usually this wide facet dimension on multimode diodes.


    Quote Originally Posted by The_Doctor View Post
    Another question...
    (Old as the hills around here, but still maybe not resolved, so I'm interested in any point of view about this.)

    If a multimode diode with narrow 'stripe width' is so fine in the 'slow' axis that it can focus like a single mode diode, is it reasonable to expect the 'fast' axis to be correctable after the same lens by using anamorphic prisms, getting a better result than 'knife-edging' three collimated single mode diodes such that their beams are parallel and in same plane?

    To put that another way: Is there some nasty habit of divergence in the multi-mode axis that prevents a fine result from the diode even after the prisms have had a go at it?

  6. #26
    Join Date
    Mar 2006
    Posts
    2,478

    Default

    Ok, looks like I mixed up the two axes.. But the question still stands because if the relation between divergence and 'stripe width' is a simple one, then I should get a multimode diode with narrow stripe, one lens, two prisms, like I described, and save all the money I'd otherwise spend on single mode diodes, extra mounts, TEC's, mirrors, alignment hassles, etc, yadda, forever and anon... And yet many people (including me) have often put emphasis on single-mode being better no matter what. So (in my best Nadsat accent), What's it going to be then, eh?

    EDIT:
    It is possible that you also have confused the axes. You say 'narrow stripe width' in a way that implies you mean the narrowEST, which is not what I meant at all. What I mean is: Two multimode diodes might have 'stripe widths' of 300 µm and 150 µm respectively. But they might both have a far thinner width (and be equal) in their other axis, the one that DOES focus like single mode. Now, the 150 µm width diode might be less power than the other one, but it seems to me that it might do better than diverge half as much; that the thing may not just be a simple ratiometric issue at all. That's what I want to know. I intend to find out by experiment, but I don't have much money so I want to get guidance to help me determine what to try first.
    Last edited by The_Doctor; 09-24-2013 at 13:05.

  7. #27
    Join Date
    Feb 2008
    Location
    Northern Indiana
    Posts
    921

    Default

    If you think of it as focusing the facet of the diode at a far distance, then with a 2X bigger facet the image will be 2X bigger if using the same power collimator. So, the divergence is going to be proportional to the facet (emitting area) dimension. The width of your beam at the lens has to do with the raw divergence of the diode.

    Beam diameter at lens = 2(focal length of lens) tan( diode raw divergence in that axis in deg.)

    So, to make the beam divergence smaller you have to make the diameter at aperture bigger.

    The emitter dimensions of a 170mw red single mode is something like 1X3um and the 300mw 71 diode around 1X30um.

    Really I don't think one can say SM is better than MM... just depends on your app. What can be said (mathematically) is single mode is usually "brighter" because the power density is higher.

    It seems that lots of MM diodes have a higher raw divergence in the FA than most SM diodes that I have looked at. But, the SM sometimes have greater raw divergence than in the slow axis.



    Quote Originally Posted by The_Doctor View Post
    Ok, looks like I mixed up the two axes.. But the question still stands because if the relation between divergence and 'stripe width' is a simple one, then I should get a multimode diode with narrow stripe, one lens, two prisms, like I described, and save all the money I'd otherwise spend on single mode diodes, extra mounts, TEC's, mirrors, alignment hassles, etc, yadda, forever and anon... And yet many people (including me) have often put emphasis on single-mode being better no matter what. So (in my best Nadsat accent), What's it going to be then, eh?

    EDIT:
    It is possible that you also have confused the axes. You say 'narrow stripe width' in a way that implies you mean the narrowEST, which is not what I meant at all. What I mean is: Two multimode diodes might have 'stripe widths' of 300 µm and 150 µm respectively. But they might both have a far thinner width (and be equal) in their other axis, the one that DOES focus like single mode. Now, the 150 µm width diode might be less power than the other one, but it seems to me that it might do better than diverge half as much; that the thing may not just be a simple ratiometric issue at all. That's what I want to know. I intend to find out by experiment, but I don't have much money so I want to get guidance to help me determine what to try first.

  8. #28
    Join Date
    Nov 2008
    Location
    Cleveland Ohio
    Posts
    2,613

    Default

    10W 1mm tem00 beam 0.50mrad divergence............opsl

  9. #29
    Join Date
    Mar 2006
    Posts
    2,478

    Default

    Quote Originally Posted by logsquared View Post
    The emitter dimensions of a 170mw red single mode is something like 1X3um and the 300mw 71 diode around 1X30um.
    I got a factor of ten error in my widths, but never mind... I understand that bit about imaging the source at distance, but is that all there is to it? If so, then it likely IS better to use multimode, one lens and two prisms, than several single mode diodes. But there are people staking tens of thousands of quid on an assertion that single mode is best for making strong red lasers for shows. If they thought that imaging source at distance was all there was to it, why would they do that? So again, is there something about the electric field propagation, or some other esoteric phenomenon of light, that prevents a multimode beam from collimating as well as a single mode beam? Never mind difference in axis divergence angles, the question is directly aimed at finding out if the difference in modal behaviour is one of specific physical quality, not only of quantity.

    Kecked, sure, OPSL=very-nice (or very+nice??) but if I add in the cost that maths really gets hairy. And I bet they are still easily killed by light reflected back at them. In ANY system that vulnerable to retroreflection death, I am absolutely determined that it must be cheap, simple, and easy to repair myself.

  10. #30
    Join Date
    Feb 2008
    Location
    Northern Indiana
    Posts
    921

    Default

    More power can be put in the same size beam (diam. + divergence) with single mode diodes. Also, the spot quality of the MM diodes are a lot worse than SM.

    Also, the 170mw SM diodes were available before the mitsu diodes. Big companies put R&D in those because that was the only real option. a few years ago.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •