Page 5 of 6 FirstFirst 123456 LastLast
Results 41 to 50 of 55

Thread: PT-40k(60k) Scanner Set

  1. #41
    Join Date
    May 2007
    Location
    1 hr from everything in SoCal
    Posts
    2,833

    Default

    Technically yes but you have to remember that to move the the mirrors as much as it sounds like you're trying to move them, the amps are still dumping a tremendous amount of power to them. That means they are generating a lot of heat. That heat will start to affect the internal parts of the galvo. Think of it like a speaker. It has no servo feedback, no damping or means of accurate control, yet when you turn the volume up, you need to dump more power into it. Granted, these are not moving air but the analogy still works because the larger the scan angle, the more power is needed for acceleration as well as the power needed for braking.
    If you're the smartest person in the room, then you're in the wrong room.

  2. #42
    swamidog's Avatar
    swamidog is offline Jr. Woodchuckington Janitor III, Esq.
    Join Date
    Nov 2006
    Location
    santa fe, nm
    Posts
    1,545,835

    Default

    set the scanning speed to 30kpps and the projection size to 0. then slowly increase the scanning size until the circle is just inside the square as shown in the test pattern link i posted.

    Quote Originally Posted by JD3 View Post
    I never go above 13k. If the cues get more complex that just means more flicker, correct? Only if I brought scan speed up to try and combat flicker would I then be over driving them.
    suppose you're thinkin' about a plate o' shrimp. Suddenly someone'll say, like, plate, or shrimp, or plate o' shrimp out of the blue, no explanation. No point in lookin' for one, either. It's all part of a cosmic unconciousness.

  3. #43
    Join Date
    Aug 2008
    Location
    UK
    Posts
    5,704

    Default

    Quote Originally Posted by JD3 View Post
    I never go above 13k. If the cues get more complex that just means more flicker, correct? Only if I brought scan speed up to try and combat flicker would I then be over driving them.
    There's your answer. The slower you run the scanners, the wider they will go.

    Just as you can run 30K scanners faster ie at more than 30K if you narrow the angle.

    None of this means though that the software will protect your scanners or 100% is a safe setting. It may be safe at 13K for your particular scan set, but 100% width at 30K could easily send your scanners to scanner heaven. You're only getting away with wider because you're running slower.

  4. #44
    Join Date
    Aug 2013
    Location
    Houston
    Posts
    537

    Default

    Quote Originally Posted by swamidog View Post
    set the scanning speed to 30kpps and the projection size to 0. then slowly increase the scanning size until the circle is just inside the square as shown in the test pattern link i posted.
    What will this determine? Aside what angle they can do 30k at.

  5. #45
    swamidog's Avatar
    swamidog is offline Jr. Woodchuckington Janitor III, Esq.
    Join Date
    Nov 2006
    Location
    santa fe, nm
    Posts
    1,545,835

    Default

    that is exactly what it will determine.

    Quote Originally Posted by JD3 View Post
    What will this determine? Aside what angle they can do 30k at.
    suppose you're thinkin' about a plate o' shrimp. Suddenly someone'll say, like, plate, or shrimp, or plate o' shrimp out of the blue, no explanation. No point in lookin' for one, either. It's all part of a cosmic unconciousness.

  6. #46
    Join Date
    Aug 2013
    Location
    Houston
    Posts
    537

    Default

    Quote Originally Posted by White-Light View Post
    There's your answer. The slower you run the scanners, the wider they will go.

    Just as you can run 30K scanners faster ie at more than 30K if you narrow the angle.

    None of this means though that the software will protect your scanners or 100% is a safe setting. It may be safe at 13K for your particular scan set, but 100% width at 30K could easily send your scanners to scanner heaven. You're only getting away with wider because you're running slower.

    Exactly. I don't understand why I would even try to run faster than they could handle and whatever angle I'm at. It destroys the beam and pretty much turns a beam into a small fan. (Draws a tail instead of a dot on the wall)

  7. #47
    Join Date
    Aug 2013
    Location
    Houston
    Posts
    537

    Default

    Quote Originally Posted by swamidog View Post
    that is exactly what it will determine.
    Lol I know, but I'm not trying to hit a certain scan speed. Just trying to run as wide and as fast as I safely can. So I do the inverse of what you suggested. I set my angle first, and then bring scan speed up.

  8. #48
    Join Date
    May 2007
    Location
    1 hr from everything in SoCal
    Posts
    2,833

    Default

    You should PM Buffo (Adam). He can tell you a great deal about scanners, tuning, angles and speeds.
    If you're the smartest person in the room, then you're in the wrong room.

  9. #49
    Join Date
    Aug 2013
    Location
    Houston
    Posts
    537

    Default

    Mainly. I'm just curious (using my method) what is the fastest scan speed the PT-40K scanners can hit (circle just inside the square) with the ILDA test image at 100% in beyond.

  10. #50
    Join Date
    May 2007
    Location
    1 hr from everything in SoCal
    Posts
    2,833

    Default

    Realistically, I wouldn't expect anything higher than 8K and even then, I am not sure. I have never tried it with mine nor will I.
    If you're the smartest person in the room, then you're in the wrong room.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •