Results 1 to 10 of 10

Thread: LASORB for DTR bundle

  1. #1
    Join Date
    Jun 2013
    Location
    Bromley, Kent. UK
    Posts
    215

    Default LASORB for DTR bundle

    Hi All

    I've purchased a Diode Bundle set from DTR and I'm wondering which LASORB I should be using for each diode. I know the Green is a new product and is ordered through 'Other' on the
    order form but which Red and Blue should I get?

    Also, with the diodes mounted in those nice copper heatsink tubes, can the LASORB's be attached to the driver output or is there a recommended way to connect them (drivers will be P3's when I get them)?
    Cheers

    Colin.

    Anyone wanting to be a politician, should automatically be excluded from being one!

  2. #2
    Join Date
    Feb 2008
    Location
    East Sussex, England
    Posts
    5,248

    Default

    Personally, I wouldn't bother with a blue Lasorb, they seem to have pretty good built in protection. Not sure about the red or the greens, but I get the impression that providing you use good anti-static precautions in the build, you shouldn't need a Lasorb now. YMMV
    Frikkin Lasers
    http://www.frikkinlasers.co.uk

    You are using Bonetti's defense against me, ah?

    I thought it fitting, considering the rocky terrain.

  3. #3
    Join Date
    Jun 2013
    Location
    Bromley, Kent. UK
    Posts
    215

    Default

    Hi Norty303

    I'd like to believe that's true. But given I've just tried to rebuild a module with a new PL450B diode taking as much ESD precautions as I have available (ESD mat, Strap, Earth connector) and have got nowhere (diode is open circuit), I'm not risking my nice new bundle if I can avoid it. Besides, I thought Blue was the worst for ESD damage.
    Cheers

    Colin.

    Anyone wanting to be a politician, should automatically be excluded from being one!

  4. #4
    Join Date
    Feb 2008
    Location
    East Sussex, England
    Posts
    5,248

    Default

    Compared to the old 660nm diodes, the A140 diodes were a revelation, although people (including myself) were very cautious with the first few batches.
    In hindsight, people found them to be (comparatively) very resilient, and subsequently quite a few people said they weren't bothering with lasorb.

    Given that the M140 and newer 9mm diodes have higher power handling, and some built in over-current protection, I would guess they are more resilient still.

    How did your PL diode come to be open circuit and is your meter able to test diode properly? Had you even connected it to a driver at that point?
    Frikkin Lasers
    http://www.frikkinlasers.co.uk

    You are using Bonetti's defense against me, ah?

    I thought it fitting, considering the rocky terrain.

  5. #5
    Join Date
    Jun 2013
    Location
    Bromley, Kent. UK
    Posts
    215

    Default

    Quote Originally Posted by norty303 View Post
    How did your PL diode come to be open circuit and is your meter able to test diode properly? Had you even connected it to a driver at that point?
    Well I soldered the wires on after covering the bare leads with some insulation and then some heatshrink over the joints. All the while I had a shorting link in the connector for good measure. I then wound back the current output of the TTL driver (meter across the pins measured 250mA initially,turned down to 140mA which is below max current according to data sheet). Powered off the driver and shorted the output pins to release any residual current. Connected my laser module, removed the shorting link and powered up. Nothing! Powered off, reinstalled the shorting link and disconnected the module. Removed the link and tested with a meter which has a diode testing position in the ohmmeter section. Tested in both directions and got an open circuit reading both ways.

    35$ +p&p gone without so much as a puff of smoke! Oh well!

    Anybody in the UK fancy rebuilding and testing my module? Give me a quote on parts (PL450B 120mW) and labour.
    Cheers

    Colin.

    Anyone wanting to be a politician, should automatically be excluded from being one!

  6. #6
    Join Date
    Nov 2008
    Location
    Cleveland Ohio
    Posts
    2,613

    Default

    dont feel bad I also had the blue pop on me in just a few hours of use. the diode is ....an issue

  7. #7
    Join Date
    Apr 2006
    Location
    Orlando, FL - USA
    Posts
    1,770

    Default

    The newer blues are definitely stronger than the older blues. No question about that! But I was still able to kill one in the lab without LASORB protection.

    By now Kvant and even many of the Chinese companies (LaserWave, Able Laser and many others) are using LASORB on substantially all of their products. It makes a difference!

    For a single Blue diode you'd need our '683 part. It's possible to put several in a string and protect them with a single LASORB but that's a bit more tricky.

    Bill

  8. #8
    Join Date
    Nov 2008
    Location
    Cleveland Ohio
    Posts
    2,613

    Default

    I just added a lasorb to each of my diodes last night. I'm tired of changing them out. It's to simple not to do it. I used a blue one for the green. Not sure if that is ok or not but it didn't change the performance.

  9. #9
    Join Date
    Jun 2013
    Location
    Bromley, Kent. UK
    Posts
    215

    Default

    Thanks for the responses guys. I think I've got what I need now. '228 for Red, '683 for Blue and '916 (the new one) for Green.
    Just waiting till I get paid
    Cheers

    Colin.

    Anyone wanting to be a politician, should automatically be excluded from being one!

  10. #10
    Join Date
    Oct 2008
    Location
    Portland
    Posts
    1,566

    Default

    I will not argue but I am 100% behind protecting every diode with a lasorb. The time it takes to change one out is worth the cost any day.

    Adam
    Support your local Janitor- not solicited .

    Laser (the acronym derived from Light Amplification by Stimulated Emissions of Radiation) is a spectacular manifestation of this process. It is a source which emits a kind of light of unrivaled purity and intensity not found in any of the previously known sources of radiation. - Lasers & Non-Linear Optics, B.B. Laud.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •