Results 1 to 6 of 6

Thread: Help Tuning a laserworld PL 800 RGB

  1. #1
    Join Date
    Feb 2014
    Posts
    2

    Default Help Tuning a laserworld PL 800 RGB

    Hi I have a Laserworld PL 800 RGB projector.

    Trying to get it tuned properly.

    There are two trim pots labelled Linearity Adjustment

    Is there a test pattern for setting this up?

    Is there away to rotate the output image form within the projector it is tilled to the left.

    Thank you

    Beyond 2000
    Mike Palma

  2. #2
    Join Date
    Jan 2013
    Location
    Detroit, USA
    Posts
    558

    Default

    Welcome to the forum!!


    First, you are going to need a large body of water...

  3. #3
    Join Date
    Aug 2008
    Location
    UK
    Posts
    5,704

    Default

    Firstly, be careful what pots you touch, as not all can be retuned easily!

    Secondly, there's an excellent guide to tuning here: http://www.photonlexicon.com/forums/...Scanner+tuning

    .......written by Adam Burns, one of the members on here.

    Thirdly, it's not easy and takes a lot of patience!

    However, if you're unsure of the pots, there will probably be someone on here who can identify them for you.

    Good luck!

  4. #4
    Join Date
    Feb 2014
    Posts
    2

    Thumbs up

    Quote Originally Posted by White-Light View Post
    Firstly, be careful what pots you touch, as not all can be retuned easily!

    Secondly, there's an excellent guide to tuning here: http://www.photonlexicon.com/forums/...Scanner+tuning

    .......written by Adam Burns, one of the members on here.

    Thirdly, it's not easy and takes a lot of patience!

    However, if you're unsure of the pots, there will probably be someone on here who can identify them for you.

    Good luck!


    Thank you for the quick reply.

    I have the technical diagram showing all the pots & their applicable labels.

    It is my understanding the DC offset pots are a no touch.

    As for patience totally agree it is a very time consuming process.

    I'm at the point where its almost there just needs a bit of tweaking & that took 2 days.

    As for the Linearity Adjustment pots they don't seem to change anything with the usual test patterns.

    Thank you again

    Have a great weekend

    Beyond 2000

    Mike Palma

  5. #5
    Join Date
    Jan 2006
    Location
    Charleston, SC
    Posts
    2,147,489,446

    Default

    Don't mess around with the linearity pots. You can screw up the image. Tuning should only be done using three pots: High Frequency Damping, Low Frequency Damping, and Servo Gain. There is one other pot that is user-adjustable - it's called Size, or sometimes Input Scale. This increases or decreases the size of the scan field.

    But the other pots are far more difficult to adjust. You really need an oscilloscope to do it correctly, and I haven't found a good tutorial on-line to explain it properly. (I've tried adjusting these myself, and it's incredibly difficult to get them right.) Bottom line: you can do a lot more harm than good by messing around with things like position scale and linearity, so stay away from those pots.

    Adam

  6. #6
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    9,890

    Default

    For position and linearity, you really need the calibration constants from the factory. Chinese producers of galvos are very reluctant to publish the numbers for position sensing's " Input volts per degree".. For linearity, you need a really, really, good single axis test jig and oscilloscope or data acquisition system. I have seen the adjustment procedure only for Cambridge products, and I've been at this a long, long time. Linearity control is highly dependent on the position sensor design, and that varies widely. As Buffo says, Linearity is the last thing I'd ever touch.

    Steve
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •