Hi all,
stumbling with trace-it for a rather difficult logo for thursday evening.
Magneetbar Logo.lds
I can't seem to get the parameters set correctly.
Any advice on how to approach this?
Michel
Hi all,
stumbling with trace-it for a rather difficult logo for thursday evening.
Magneetbar Logo.lds
I can't seem to get the parameters set correctly.
Any advice on how to approach this?
Michel
--------------------------------------------------------------------------------------------------------------------------------------------
Michel Rietveld @ Utrecht The Netherlands
FB3, BEYOND Ultimate, 3xFB4, apc 40
1x5W RGB 637nm 1.3W, Edison Blue 2.5W 445nm and CNI 2.5W 532nm Greenie with Pico driver with DT40Kpro scanner set
2x3W RGB DT30 scanner set
Don't take this the wrong way Michel but you got to put the pipe down... That is definatly an ambitious logo you got there.
I can't see getting Magnet to scan well, even using a generic block font much less MagnetBar. I suspect you want the "texture" or outline of each letter like the "font" in the logo picture too huh? I would think about doing each letter individually as a seperate frame and try to make some sort of animation ; the problem will be using them all at the same time. Maybe walk them across the screen one at a time, I dunno; I envision a whole lotta points when I look at that logo. Maybe one of the more experienced professionals can suggest something crazy.
Love, peace, and grease,
allthat... aka: aaron@pangolin
You're definitely going to need to put it in some sort of animation, it's just wayyy too complex for all at once.
raster it.
chad
When the going gets weird, the weird turn pro.
--------------------------------------------------------------------------------------------------------------------------------------------
Michel Rietveld @ Utrecht The Netherlands
FB3, BEYOND Ultimate, 3xFB4, apc 40
1x5W RGB 637nm 1.3W, Edison Blue 2.5W 445nm and CNI 2.5W 532nm Greenie with Pico driver with DT40Kpro scanner set
2x3W RGB DT30 scanner set
Hi PJ, thanks for jumping in, what is the reason behind the question, will it be a different approach for long compared to a short scan period because it could be harmfull to the scanset?
i have a dt40k pro and it would be nice to put the logo for a short time on the wall.
already replied to this thread 2 times, from work and from phone just don't see the updates, will mail you as well.
--------------------------------------------------------------------------------------------------------------------------------------------
Michel Rietveld @ Utrecht The Netherlands
FB3, BEYOND Ultimate, 3xFB4, apc 40
1x5W RGB 637nm 1.3W, Edison Blue 2.5W 445nm and CNI 2.5W 532nm Greenie with Pico driver with DT40Kpro scanner set
2x3W RGB DT30 scanner set
--------------------------------------------------------------------------------------------------------------------------------------------
Michel Rietveld @ Utrecht The Netherlands
FB3, BEYOND Ultimate, 3xFB4, apc 40
1x5W RGB 637nm 1.3W, Edison Blue 2.5W 445nm and CNI 2.5W 532nm Greenie with Pico driver with DT40Kpro scanner set
2x3W RGB DT30 scanner set
No problem michel,
I have my ways to do these kind of things hehe
Making the unscannable be scannable is what I do.
Your scanners will be ok with the scanning, no damage on long term use has been found on my scanners because i give my scanners a break every now and then to relax up.
Also yes guys that scan contains the eyes, iruses colors and everything.
Except a small wobbly line everything is in there.
I have a logo service soon up so "seemingly" impossible logo's can be redirected to me.
Here's a slightly better foto from what michel got (no exposure tweaks)
Yes I know this camera is shit.
Last edited by masterpj; 06-14-2012 at 02:21.
Nice!
Hand drawn with some little point-pulling ?
At what angle, at what fps ?