Laser kit clear out!

[ams09]

Hi Danielbriggs,
Interested by your two Laserwave head, Red and Green ( i don't know Lasarwave module... ) and perhaps by the RGBLS 473nm head at 200€. The nominal power output and colour is labeled by the last four digits on the sticker (ex: RGBxxxxxxxxxxxxxxB600 for Blue 600mW ). Can you give me this end.
Regards, Christophe

[Bradfo69]

PM sent to revisit the 2 year old 473 discussion, and about the modem.

[danielbriggs]

the last four digits on the sticker (ex: RGBxxxxxxxxxxxxxxB600 for Blue 600mW )

B500

@Brad... going through PM's now.

[ams09]

Hello,
B500, ok. Pump diode 808nm, 4W (without FAC) driver calibrated at 3.6A @ mod +3V. Can you post one pics of the driver ?
Thanks and regards.
Christophe.

[danielbriggs]

Can you post one pics of the driver ?:

I've taken the side off to get a good view of the boards:

[ams09]

Hi Danielbriggs,

Thanks for pics. I have the same inclosure, but not same PCB on my B600 ( dual unit ), and not same PCB too on my B250 single unit. I have many other head and drivers from RGBLS, but it's impossible to have any informations from them. All of their drivers are complicated, with many wires in every way...
If I did not get an answer to my offer, I think it is because he has gone to Brad ...???
@ Brad: If i can help you in the future about this, tell me...
Regards at all.

[danielbriggs]

Hi AMS,
€200 is a little low, but thanks for the offer; no deals have been done yet.

[Bradfo69]

Hi ams09 - Nope not me this time. I'm just working on the 473 blue and the modem. (Although the clamps, Pyro controller and DMX board keep pestering me...)

[ams09]

Re... Thanks again Daniel...
Brad, OK... if you need some informations or parts about 473nm DPSS module, i have several of them ( working an defect ) from RGB, CNI and others.
At this time, i can't work on DPSS, i have not working room, ( yes, i have...but with not heating system, and i can not work on DPSS and on laser application in general with 10/15°C )
I thought of transferring a party in my house, but my wife has a different idea about the layout and decoration...
Merry Christmas for you, and all read this here.
Regards, Christophe.

[danielbriggs]

Hi all,
Another day of clearing more superfluous parts from the office...

Part 3!

All offers considered...
Most going on eBay tomorrow, +15% on the price to cover fees, contact me directly via PM or email if interested in any bits.

As for the parts in need of repair, I don't have the time to spend fixing them, so offered up here fairly cheap for anyone keen to have a go.


First, lots of smoke machines!

ZR44
£SOLD

The ZR44 Jem smoke machine has a PCB fault, there is no power going to the heater. Includes remote.





ZR33 #1
£SOLD

This ZR33 Jem smoke machine works perfectly, with a remote, includes half a tank of fluid!





ZR33 #2
£SOLD

This ZR33 Jem smoke machine has a PCB fault, the heater only powers when the fog button is pressed. No remote, no fluid.
Includes replacement PCB which might be dodgy, untested.





ZR33/44 Flightcase
£SOLD

A superb condition flightcase for a ZR33 / 44 by flightcase warehouse; clean condition.





19" 2U Flightcase
£70

Like-new condition flightcase for 19" equipment, 750mm deep, with retractable handle and wheels.





Behringer BCF2000 MIDI Controller
£SOLD

Good condition Behringer BCF2000 MIDI controller, works well, all motorised faders work. Includes power cable, no USB cable.





Flightcase #1
£25

Average condition flightcase.
Outside dimensions 63x36x37cm





Flightcase #2
£35

Good condition flightcase; a few labels + tape covering it.
Outside dimensions: 61x36x32 (excluding wheels).
Unit has 4x wheels on base.





Laserscope Orion - Conversion almost complete
£SOLD

A converted Laserscope Orion that was nearly completed in conversion.
Chassis rebuilt, but ALE died after a few hours of use.
Includes a TTL galvo-retroreflector blanking system.
Needs: basic oven controller + ALE repair.
Last time the resonator was powered it did 28W, which is good for an Orion. The lamp and filter were replaced recently and has less than <10hrs.





GLP Messenger Lighting Desk
£100

GLP Messenger lighting desk in superb physical condition, appears to output data, but nothing displayed on screen.
Used once or twice then LCD stopped working.
Bought from new @ £1,200(!)





Powerdrive Stand #1
£60

A larger PowerDrive EasyHoist 330 PowerDrive stand, extends to 3.3m at 60kg.
Good condition.
£350 new! https://www.leisuretec.co.uk/product...ls/webpow00023





Powerdrive Stand #2
£50

A normal sized PowerDrive stand (exact model unknown). Includes spigot adapter pictured.
Good condition.





Melles Griot 532nm DPSS Laser #1
£SOLD

A used Melles Griot DPSS green laser module. This particular unit outputs <1mW of 532nm at operating current.
Includes full manual and factory RS-232 software.





Melles Griot 532nm DPSS Laser #2
£SOLD

Another used Melles Griot DPSS green laser module. This doesn't output any green, plenty of IR.
Includes full manual and factory RS-232 software.





Oasis 150 Solid State Chiller
£SOLD

A great little solid state chiller, 4-40˚C adjustment setpoint.
Sells for over £180 used, >£520 new!
Includes PSU brick, no IEC (as localisation/plug dependant)
(Includes PDF manual on request for RS-232 command list etc.)





Coherent Labmaster Ultima
£SOLD

Good condition Coherent LabMaster Ultima power meter. Works really well!
Single channel model with ModeMaster firmware (requires external ModeMaster device)
Has RS-232 port + Printer + analog I/O. NiCad battery would probably need replacing for battery operation; functions perfectly on mains.
Any Coherent LM power meter heads work (available below or on eBay).
Includes PSU (UK Plug) and PDF full manual.





Coherent LM-80
£SOLD

Good condition Coherent power meter head, 80W max power. Clean condition absorber surface. No stand.
Works (tested) with the Coherent LabMaster Ultima above or any other meter that accepts LM series heads. If interested in a bundle, please get in touch for a combined offer price.





Coherent LM-100
£SOLD

Good condition Coherent power meter head, 100W max power. Fair condition absorber surface. Includes stand.
Works (tested) with the Coherent LabMaster Ultima above or any other meter that accepts LM series heads. If interested in a bundle, please get in touch for a combined offer price.





Oxford Lasers CU-10 Copper Vapour Lasers #1 + #2
£SOLD

This one really makes me sad
Up for sale are two (2!) Oxford lasers CVL CU-10's.
One works perfectly, as demonstrate by this numpty pressing buttons to coax it into life here:





The other one... doesn't quite run (yet!)
I've rebuilt the PSU as per the factory schematics, and all parts are intact.
The vac line system has also been sorted and the tube pumps down correctly.
The only problem is I can't get a discharge in the tube. The HV supply engages, but past 4kV the variac begins to arc internally, so I back it right off.
I can't really spend any more time troubleshooting this, so #2 offered as-is. (#1 definitely works well!) Good for either an easy fix to those in the know, or worst case.... spares for the 1st.
Requires CP grade Neon, which I have a near full cylinder of, so might be a strike a deal on that. Gas is fully paid for, however cylinder rental is from BOC on our account.
I'd REALLY really really like to sell both units as one lot, but will split if both go.
Includes printed + bound manual + schematics of CVL, vac pump and thyratron (i.e. all info I've gathered on these.)
All sensible offers welcome.







That's it for now!
Prices above include non-eBay PL discount, but all offers welcome.

All items sold as-is, as fairly well described + tested where appropriate.
As before, all items exclude and PayPal fees, posted etc.
Collection preferred (+free cup of tea + biscuits on collection from the office!) but postage can be arranged internationally at cost on request.

Cheers,
Dan