Page 3 of 3 FirstFirst 123
Results 21 to 27 of 27

Thread: My latest project

  1. #21
    Join Date
    May 2014
    Location
    Barcelona, Spain
    Posts
    439

    Default

    Well, I have several SMPS500R dual 24V PSU here. Its dual 24V 500W on a 100x100mm footprint, to power entire projector....
    But on dual 24V PSU, need also DC-DC convertors 24v-12V @hight amperajes for my diodes and these are not cheap, so I would prefer to work entire projector @12V and step up to dual 24V ONLY for scanners.
    http://connexelectronic.com/product_...le0h7lvvekhck3
    IMG_5612.JPG


    Quote Originally Posted by masterpj View Post
    I have had little luck finding DC/DC converters providing any decent wattage output. It all seems to be in the microamp/miliamp range at best. The microamp one cost about $8. I wouldn't mind the dc converters to being a tad larger.. so far the only alternative would be dual rail power supplies.. but even those can be a pain to find sometimes. I guess with everyone wanting all single rail powered equipment this is a reason why these components cost so much. Alternatives are always welcome this is where I got stuck with on my portable build.. the differential supplier.

    I did make the simplest circuit with a virtual ground but it got unbalanced so quickly that it was unusable for being a scanner power supply.
    Maybe the op-amp one could work.. I don't know.
    http://tangentsoft.net/elec/vgrounds.html

  2. #22
    Join Date
    Mar 2007
    Location
    Portland Oregon
    Posts
    118

    Default

    Hi all
    A few comments.

    Only Isolated converters can be used in this circuit. Most DC/DC have the input and output ground connection tied together. They are cheap but will not work together in series.

    I find no problems with my scanner performance using just 1.25 A supplies. However, it would be quite easy to buy 4 each of the 12 v 2.5A and wire them appropriately fro +- 24v.

    Filter capacitors to use suggestions 47uf 50v multilayer ceramic along with 47uf 35valuminum polymer capacitors. Apply capacitors across 12v input and each 24v rail.

    These power supplies are quite efficient and produce little heat. If you can see in my photo, they are thermal epoxied to a copper strip which is screwed to the heartsick.

    Laserbiker

  3. #23
    Join Date
    May 2014
    Location
    Barcelona, Spain
    Posts
    439

    Default

    Many thanks Laserbiker for sharing info,
    so could be the wiring diagram like this?:
    FullSizeRender.jpg
    Have the capacitors polarity orientation like electrolytic capacitors (+ & -)?
    Many thanks!!!!



    Quote Originally Posted by laserbiker View Post
    Hi all
    A few comments.

    Only Isolated converters can be used in this circuit. Most DC/DC have the input and output ground connection tied together. They are cheap but will not work together in series.

    I find no problems with my scanner performance using just 1.25 A supplies. However, it would be quite easy to buy 4 each of the 12 v 2.5A and wire them appropriately fro +- 24v.

    Filter capacitors to use suggestions 47uf 50v multilayer ceramic along with 47uf 35valuminum polymer capacitors. Apply capacitors across 12v input and each 24v rail.

    These power supplies are quite efficient and produce little heat. If you can see in my photo, they are thermal epoxied to a copper strip which is screwed to the heartsick.

    Laserbiker

  4. #24
    Join Date
    Mar 2007
    Location
    Portland Oregon
    Posts
    118

    Default

    Jors

    Your drawing is correct. Only the electrolytic capacitors must be connected correct polarity or they will
    blow up. Polarity does not matter for the chip capacitors.
    Good luck with your project
    Laserbiker

  5. #25
    Join Date
    May 2014
    Location
    Barcelona, Spain
    Posts
    439

    Default

    Many thanks Laserbiker, but sorry, still confused....
    Is 47uF 35V electrolytic (polarity) capacitor?
    About 47uF 50v multilayer ceramic (chip?)... is really 47uF? or 47pF? I haven't found ceramic with 47uF (
    Sorry for my confusion and thanks again

    Quote Originally Posted by laserbiker View Post
    Jors

    Your drawing is correct. Only the electrolytic capacitors must be connected correct polarity or they will
    blow up. Polarity does not matter for the chip capacitors.
    Good luck with your project
    Laserbiker

  6. #26
    Join Date
    Aug 2009
    Location
    Churchill(hour S from Houston)
    Posts
    1,354

    Default

    you are going to love NWLEM as much as the guys will enjoy meeting you and seeing this awesome build--you will never want to miss another LEM...TY for the very helpful thread.


    VR hak
    BEYOND-FB3/APC40Mamba Black(clone & currently on loan) 2X 5paghetti & 2 I-Show 2X KGB 1000mW 532 DT40K (pair)XFX 1300 RGB full color RGB 30K DIY 3.5WRGB work in progress et al..assorted ttl chi-jectors--LOTS of LUMIA DIY pjs-
    Powered by Pangolin
    Former (2.5 yrs) ILDA Member- :-(
    uncertified ILDA LSO -- dont ask

  7. #27
    Join Date
    May 2014
    Location
    Barcelona, Spain
    Posts
    439

    Default

    Hi Laserbiker,
    PLease could you help?
    Multilayer ceramic 50V capacitors should be 47uF or 4,7uF or 0,47uF??
    47uF ceramic are uncommon and really expensive...
    http://www.digikey.com/product-detai...069-ND/1913138

    and on Farnell, several at 47uF but NOT 50v
    http://es.farnell.com/webapp/wcs/sto...e&pf=510048804

    Many thanks!!


    Quote Originally Posted by laserbiker View Post
    Hi all
    A few comments.

    Only Isolated converters can be used in this circuit. Most DC/DC have the input and output ground connection tied together. They are cheap but will not work together in series.

    I find no problems with my scanner performance using just 1.25 A supplies. However, it would be quite easy to buy 4 each of the 12 v 2.5A and wire them appropriately fro +- 24v.

    Filter capacitors to use suggestions 47uf 50v multilayer ceramic along with 47uf 35valuminum polymer capacitors. Apply capacitors across 12v input and each 24v rail.

    These power supplies are quite efficient and produce little heat. If you can see in my photo, they are thermal epoxied to a copper strip which is screwed to the heartsick.

    Laserbiker
    Last edited by jors; 01-02-2015 at 10:41.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •