Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: PT-A40 Feedback pinout?

  1. #1
    Join Date
    May 2014
    Location
    Barcelona, Spain
    Posts
    439

    Default PT-A40 Feedback pinout?

    Hi!
    I'd like to install scan-fail (mylaserpage.de) on my PT-A40. However I can't find single-ended feedback signal (position detector) pinouts on scanner drivers :(
    I ve pm'ed Omar & emailed phenixtechnology but not response yet :(, so maybe any electronics 'guru' here could help please?
    Thanks!
    Click image for larger version. 

Name:	image.jpg 
Views:	34 
Size:	599.1 KB 
ID:	47058

  2. #2
    Join Date
    Feb 2008
    Location
    East Sussex, England
    Posts
    5,248

    Default

    I have 2 sets here waiting to be put in projectors and I'll be needing that too. I'll see if i can find anything.


    edit, ok just had a look and my best guess is the 2 pin header just above the signal input. You'll see its only got the positive marked on one of the pins (the one nearest the signal input). Scanfail feedback only uses the positive from the amp.
    PRobably easiest way to test if you haven't got a scope is to connect a voltmeter to the pin and the signal ground and try displaying an opening and closing circle. IF the average value read goes up and down then this is probably your feedback.
    Last edited by norty303; 05-11-2015 at 10:57.
    Frikkin Lasers
    http://www.frikkinlasers.co.uk

    You are using Bonetti's defense against me, ah?

    I thought it fitting, considering the rocky terrain.

  3. #3
    Join Date
    May 2014
    Location
    Barcelona, Spain
    Posts
    439

    Default

    Thanks Norty!
    Ohhh yes, could be! . 1st pin is G, the other is labeled "+"... hope you're right and this is Fb. Well, so... waiting for Phenix technololgy response, I have no skills on electronics.
    Click image for larger version. 

Name:	image.jpg 
Views:	41 
Size:	414.9 KB 
ID:	47062

  4. #4
    Join Date
    May 2014
    Location
    Barcelona, Spain
    Posts
    439

    Default

    Norty,
    Right now received email from Ella (Phenixtechnology). She says those pins are FB signal

  5. #5
    Join Date
    Jun 2011
    Location
    China
    Posts
    148

    Default

    Click image for larger version. 

Name:	11.png 
Views:	36 
Size:	535.1 KB 
ID:	47076

    Yes, that is~

  6. #6
    Join Date
    Feb 2008
    Location
    East Sussex, England
    Posts
    5,248

    Default

    Omar, are you pointing to the 3 pin header? I thought that was the differential signal input?
    We thought it is the 2 pin header to the left of the 3 pin header
    Frikkin Lasers
    http://www.frikkinlasers.co.uk

    You are using Bonetti's defense against me, ah?

    I thought it fitting, considering the rocky terrain.

  7. #7
    Join Date
    Jun 2011
    Location
    China
    Posts
    148

    Default

    Click image for larger version. 

Name:	2121.jpg 
Views:	45 
Size:	645.6 KB 
ID:	47077

    2 pin header for Feedback, 3 pin header for Signal.

  8. #8
    Join Date
    May 2014
    Location
    Barcelona, Spain
    Posts
    439

    Default

    Thanks!!

  9. #9
    Join Date
    Feb 2008
    Location
    East Sussex, England
    Posts
    5,248

    Default

    I contacted Mimi at Goldenstar who sold me my PT-A40's and she managed to get a manual from Phenix.

    I've uploaded it here in case its of use to anyone further.

    I'll see if I can get it somewhere else too, like the ftp if that's still used. we could do with a repository for this stuff really, so that we can archive documentation for products that go out of production.


    Click image for larger version. 

Name:	PT-A40 User Manuel.pdf 
Views:	64 
Size:	406.3 KB 
ID:	47078



    Jors, don't forget, with Guido's board you only connect the + from the scanner feedback to the board, not the negative as well
    Frikkin Lasers
    http://www.frikkinlasers.co.uk

    You are using Bonetti's defense against me, ah?

    I thought it fitting, considering the rocky terrain.

  10. #10
    Join Date
    May 2014
    Location
    Barcelona, Spain
    Posts
    439

    Default

    Many thanks Norty,
    Sorry but, Why not connect negative Fb?
    Fb negative out from PT-A40 driver is G (0v). Is Guido's SF negative input (Fb) also G (0v)??
    If so...it doesn't matter if I connect or not feedback negatives, because anyway negatives will be tied together at 0V(G) thru my central (negative) grounding point that goes to ILDA pin 25... isn't it?
    Click image for larger version. 

Name:	SF.jpg 
Views:	19 
Size:	98.4 KB 
ID:	47079

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •