Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 22

Thread: DT-50W

  1. #11
    Join Date
    May 2007
    Location
    1 hr from everything in SoCal
    Posts
    2,833

    Default

    Quote Originally Posted by norty303 View Post
    Someone with more knowledge than me will be able to say what galvo it has been cloned/plagiarised heavily from, no doubt.
    Certainly no more knowledge than you but they look like a spitting image of the CT-6215HPs. Well, maybe not as long... CT-6210HPs?
    If you're the smartest person in the room, then you're in the wrong room.

  2. #12
    Join Date
    Dec 2008
    Location
    veenwouden
    Posts
    2,579

    Default

    There,s your answer why cambridge went out of the lasershow bussiness. Chinese copied there product massively and because of that the whole market went down. They are cheaper and do just fine for 95% of all jobs.

    Cambridge are in a werstern country with higher costs production costs so not worth the effort since the market is small and competition is fearse. Although cambridge scanners are still the best ones the biggest market ( wich is beamshows) doesn,t need that super fast accurate ones. Chinese are good in cheap and average. Pangolin came on the market with there 506 and a month later Phenixtechnology came with their PT-A series. Now DT comes with these and maybe other series.
    You see the exact same pattern in the projector market. There are over 100 manufactures and they try to compete to by being the cheapest wich in a few years half of the manufactures go either bankrupt or switch to a different market.


    Interested in 6-12W RGB projectors with low divergence? Contact me by PM!

  3. #13
    Join Date
    Jul 2010
    Location
    Netherlands
    Posts
    3,322

    Default

    actually cambridge had issues at their factory from what I heard on top of having a flood close or at the factory in the past.
    I'd argue when you say cambridge are still the best ones.. yes they are sturdy like a brick but time catched up with them. Their power supply requirements (or at least the CTHP) is huge and because it's all analog the requirement of a really clean power supply (toroidal) seemed to be needed from what I had seen.

    The chinese can copy the analog designs because it's easier to reverse engineer but the digital designs is where this stops.. at that point you need to poke around in the dye as security is set within a DSP's firmware so that's where the copying road ends really.

    The scanner performance we are approaching/have approached now require something like a DSP to perform optimally.
    Is this product appealing: yes it still is. Will chinese provide the best of scanning: Not by a mile.

  4. #14
    Join Date
    Feb 2016
    Posts
    12

    Default

    Not sure if this is going to be cheap cheap , I think when they reach final product status prices will be in a 600 $ range ? + shipment + tax
    On Goldenstars FB page as Norty mentioned Mimi said they are still pushing design changes towards DT so is this a final product ?

  5. #15
    Join Date
    Aug 2008
    Location
    UK
    Posts
    5,704

    Default

    One interesting point I noticed from the Data Sheet posted by Norty, - DT50W but ILDA scan speed is 40kps! Doesn't that make them DT40W's?

    ..and isn't the max scan angle less than that claimed for the DT40W (95 degrees), which also claim 40kps ILDA?

    http://www.dtelectronic.cn/production.asp?ArticleID=54

    Maybe I'm missing the point of these!

  6. #16
    Join Date
    May 2007
    Location
    1 hr from everything in SoCal
    Posts
    2,833

    Default

    Quote Originally Posted by White-Light View Post
    DT50W but ILDA scan speed is 40kps! Doesn't that make them DT40W's?
    Assuming that the spec sheets are correct, this is an age-old trick that a lot of campanies have used; Come out with several products with performance specs that are a "part" of the product name and after a while, rename the product so people automatically think that the specs are still a part of the product name, even though they are not. DT-25 = 25Kpps scanners. DT-30 = 30Kpps scanners. DT-40 = 40Kpps scanners. DT-50, well, "we'll just just call them 50 and people will think they are 50K scanners".
    Last edited by absolom7691; 04-28-2016 at 02:34.
    If you're the smartest person in the room, then you're in the wrong room.

  7. #17
    Join Date
    Apr 2016
    Posts
    162

    Default

    To me it looks like scanner that can deliver the same performance as DT40W but with much bigger mirrors. Am I right?

    Probably something DT made to compete with the new Phenixtechnology "PT-A" series scanners.

    THe ordinary PT scanners were much cheaper than DT but performed pretty well. I wonder if the cost difference between this and the PT-A30 or PT-A40 will be as noticeable.

  8. #18
    Join Date
    Jun 2010
    Location
    Australia
    Posts
    3,733

    Default

    Those scanners dont appear to be perfectly orthagonal.
    This space for rent.

  9. #19
    Join Date
    Oct 2014
    Location
    Orlando, FL
    Posts
    387

    Default

    Theyre not supposed to be inimagine. It looks like theyre trying to implement a setback to save some mirrror inertia
    Sincerely,
    Ryan Smith
    ScannerMAX Mechanical Engineer
    ryan {at} scannermax.com

  10. #20
    Join Date
    Aug 2010
    Location
    London or Spain depending on the weather
    Posts
    1,390

    Default


    Quote Originally Posted by dnar View Post
    Those scanners dont appear to be perfectly orthagonal.
    That would change the "rns0504" maths a tad !
    Cheers

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •