Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: Strange dots after replacing TTL with Analog

  1. #1
    Join Date
    Dec 2010
    Location
    Wellington, New Zealand
    Posts
    39

    Default Analog issues with RGB laser..

    Hey all, im pretty new to the forum so apologies if this is in the wrong place!

    I think my laser is 'clipping'

    I recently got my first laser projector, full RGB with analog modulation. However the manufacturer informed me they shipped it with TTL on the green module, and shipped me an analog controller.

    All seemed simple enough to replace it after opening the projector and tracing the cables, i swapped it over, and tested it before putting the top back on, however was greeted with two blue dots near the bottom right.They don't move despite patterns playing, but i havent hooked it up to QuickShow to get a more accurate image of whats going on.

    Heres a short youtube video displaying the issue - https://www.youtube.com/watch?v=IgnKfjh1UtE

    Heres a picture of it during a pattern - http://iforce.co.nz/i/fbrzxrup.hwu.jpg, as you can see at the bottom .. nor do they change color when I apply an RGB filter via QuickShow

    Internals - http://iforce.co.nz/i/2u5xtbvv.whz.jpg


    The order of the lasers is B G R .. if i manually block the blue, the dot changes to green .. if i manually block blue and green theres no dots, so my thinking is a misaligned mirror on the green? (if thats the right word)

    Could it be a faulty Analog controller ? Also whats the correct wording for this piece.

    I don't really know enough about this to tell whats going on Im pending a fog machine to arrive in the next couple of days .. can anyone shed some light as to where i should begin?

    Thanks in advance!
    Last edited by ReaperZ; 07-25-2016 at 02:22.

  2. #2
    Join Date
    Mar 2010
    Location
    Raleigh, NC
    Posts
    2,314

    Default

    Is there leakage from the case? It is normal to have some stray beams that go through the dichros but the case usually terminates them. Is the cover on your case? If not, put it back on and call it a day. If it isn't leakage then something is commanding the dots to be drawn at that location, which would require something really weird going on, probably in the software.

  3. #3
    Join Date
    Feb 2008
    Location
    East Sussex, England
    Posts
    5,248

    Default

    I can't see any of your images, but when you remove the casing, does it expose the front of the projector fully?
    If so, what you are seeing is probably leakage from mirrors/dichros, either passing through, rather than reflected, or being reflected off the back face of a dichro.
    Put your hand in front of each mount in turn and you should see where the dots are coming from.

    This is also a useful lesson in safety, as it will make you aware that laser emissions can come from unexpected places, not just the module aperture or scanner aperture.
    Generally quite low power, but when you start dealing with multi-watt modules, 3% leakage can still amount to a few hundred mW, especially if its carrying a couple of wavelengths
    Frikkin Lasers
    http://www.frikkinlasers.co.uk

    You are using Bonetti's defense against me, ah?

    I thought it fitting, considering the rocky terrain.

  4. #4
    Join Date
    Dec 2010
    Location
    Wellington, New Zealand
    Posts
    39

    Default

    Well now I feel silly, but yet educated.. It was indeed what you both mention, stray dots which the front of the casing terminated, as removing the casing exposes the front of the setup.

    It seems my strategy of "test it before screwing the chassis together" from numerous pc building / repair days tripped me up here

    It seems in this case it was the mirror for passing / reflecting in front of the green module causing the issue, and now that makes sense why they wouldn't have been moving with the images, because it was happening before the dichros!

    Definitely a useful lesson in safety norty303, I totally understand what you mean.

    Is it bad that this makes me want to break / play / upgrade things already? I think I'm hooked!

  5. #5
    Bradfo69's Avatar
    Bradfo69 is offline Pending BST Forum Purchases: $47,127,283.53
    Join Date
    Jul 2010
    Location
    Wilmington, DE
    Posts
    6,207

    Default

    Quote Originally Posted by ReaperZ View Post

    Is it bad that this makes me want to break / play / upgrade things already? I think I'm hooked!
    Welcome to the slippery slope of insanity.
    PM Sent...

  6. #6
    Join Date
    Feb 2008
    Location
    East Sussex, England
    Posts
    5,248

    Default

    Quote Originally Posted by ReaperZ
    and now that makes sense why they wouldn't have been moving with the images, because it was happening before the dichros!
    Actually, it was happening before the scanners. The dichros are just the bits of coloured glass to combine the different wavelengths. They do nothing to move the beam around (hopefully!), unless you are adjusting the alignment.
    Frikkin Lasers
    http://www.frikkinlasers.co.uk

    You are using Bonetti's defense against me, ah?

    I thought it fitting, considering the rocky terrain.

  7. #7
    Join Date
    Dec 2010
    Location
    Wellington, New Zealand
    Posts
    39

    Default

    Ah, sorry about the incorrect terminology, and thanks for correcting me!

    Picture for future reference in case someone else stumbles across this thread

    [EDIT] Dicho's


    I don't want to go to work today, I want to stay home and learn and experiment!
    Last edited by ReaperZ; 07-24-2016 at 15:41.

  8. #8
    Join Date
    Jun 2013
    Location
    Bromley, Kent. UK
    Posts
    215

    Default

    Above picture title says 'Galvo', should say 'Dichros'. Galvos are the 'motors' in the scanner head that move the mirrors.
    Cheers

    Colin.

    Anyone wanting to be a politician, should automatically be excluded from being one!

  9. #9
    Join Date
    Aug 2009
    Location
    Churchill(hour S from Houston)
    Posts
    1,354

    Default

    you are confusing 'controller' and driver..
    .. you will hopefully get fixed here.

    check a few of these NZ places-- not all can work on show laser PJs.. so it will take some digging to get help in NZ. gave your name to a member in NZ ( at least at one time)

    https://www.google.com/search?q=Lase...and&gws_rd=ssl

    this fix would be a good one to TShoot via SKYPE..
    so no need to be a KIWI in order to help.
    btw that same LK projector had a scan blocker with a mind of its own.. most times requiring an removal front& top to push the 'flag' back out of the way.. another owner finally 'tied' his in some way.
    only two times can I remember it going back in place by itself..out of 6 or 7 times.. no idea why it does its thing..except when I tried to get a small white dot.. -'system' sees that as a scan fail.

    hak


    hak
    BEYOND-FB3/APC40Mamba Black(clone & currently on loan) 2X 5paghetti & 2 I-Show 2X KGB 1000mW 532 DT40K (pair)XFX 1300 RGB full color RGB 30K DIY 3.5WRGB work in progress et al..assorted ttl chi-jectors--LOTS of LUMIA DIY pjs-
    Powered by Pangolin
    Former (2.5 yrs) ILDA Member- :-(
    uncertified ILDA LSO -- dont ask

  10. #10
    Join Date
    Nov 2008
    Location
    Orkland, NZ or Bavaria, Germany
    Posts
    169

    Default

    Hello ello! Let me know if you need any help there, are you in AKL?

    Looks just like stray beams from dichros indeed.TTL to Analogue driver conversion sounds a little strange. Most DPSS drivers are tuned to each laser head, so it may need some tutuing to get it running right (assuming it's a DPSS like it looks to be).

    Happy lasing

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •