Results 1 to 6 of 6

Thread: Maxyzmodules 225mW RED module, singles and duals

  1. #1
    Join Date
    Feb 2005
    Location
    Florida
    Posts
    802

    Default Maxyzmodules 225mW RED module, singles and duals

    Decided a new thread was in order, Last one was not editable since the new site software upgrade

    For Sale:
    As seen on ebay and on this site !!!
    Maxyzmodules RED 660nm 225mW laser module

    As of : October 23 2007 (updated EUR)

    for Photolexicon members ..
    269.95USD or 189.97EUR each --
    Shipping is 15USD for USA and Canada
    25USd or 17.55EUR for International orders
    284.95USD Total for USA or 294.95USD (207.52EUR) total for International

    That's 539.90USD for a Pair ...(378.99EUR)
    Same price shipping...Limited time offer ...
    They come Analog modulation...Altho , You can use the analog units in TTL configuration. These will include the new driver board with full blanking to well
    over 30khz. (useful to at least 100khz)

    Also included FREE is a 9volt wallwart power supply (while supply lasts) they operate from 120/220ac 50/60hz

    If you need a mounting plate, We offer them at 25USD 17.55EUR each, These are for mounting of a single unit.

    If you need a dual mounting plate for combining a pair 45USD 31.59EUR each.
    ..set-up and predrilled for mounting of a MM-1 or equivalent mirror mount and a MM-1 /BS or equivalent like the one pictured in below.

    We still have a few for you guys that want to roll your own:
    Laser_line PBS cube 165.00USD or 115.81EUR
    Laser-Line PBS cube mounted to MM1 or KMS is 235.00USD or 164.95EUR
    Laser-Line mirror mounted to MM1 or KMS is 75.00USD or 52.65EUR
    Plus shipping.

    Grab a couple and find a Beamsplitter or Pol Cube and combine them for more power... Typical output is about 440mW out.
    If you buy 2 , I will set one of them up opposite polarity for easier combining!!!

    If you buy the whole set-up its 830USD plus 20USD in USA/Canada , 850USD total or 596.62EUR plus 21.06EUR international shipping , 617.68EUR total

    Each unit is handcrafted. therefore.. great care is put in each unit before they leave..
    The power is doublechecked with a Melles Griot and Scientech broadband power meters.
    All parts are NEW .. except the heat sink which is black anodised However , We have just started to paint them with a special FLAT BLACK paint.
    The beam diameter is less than 2.5mm (always) mostly around 2.2mm and divergence less than 1.0mR. Typically .8mR.

    Only a few complete set-ups are available at a time.. so you may have to wait a day or two for us to build. We dont like having stuff laying around.

    Oh and dont forget, if paying by PAYPAL please add the 4 percent they charge for their cut Thats about 34.00USD or 23.80EUR for the duals.

    The combined plate has been redesigned slightly so no holes are covered and are spaced correctly.
    Still using 3/8" holes spaced 5" each way on the 6" by 6" plates.

    The diodes are NOT the small 100mW DVD diodes...!!!
    And we thank everyone who has bought these...enjoy

    Please PM me for more info
    Thanks
    Attached Thumbnails Attached Thumbnails IMG_1179s.jpg  

    carey_450_2.sized.jpg  

    IMG_1173s.jpg  

    200red_fire.sized.jpg  

    Last edited by marconi; 10-23-2007 at 09:40.
    "My signature has been taken, so Insert another here"
    http://repairfaq.ece.drexel.edu/sam/laserfaq.htm
    *^_^* aka PhiloUHF

  2. #2

    Default

    I want one, please pm of email me
    rbrooks@purdue.edu

  3. #3
    Join Date
    Jan 2007
    Location
    Cupertino, California
    Posts
    2,130

    Default

    Click on his avatar, then click on the link that says private messaging.
    CLICKY!!!

    Admin: In the immortal words of Captain Planet: YOU HAVE THE POWER
    Admin: (To quit being a bitch)

  4. #4

    Default

    Quote Originally Posted by Laser Ben View Post
    Click on his avatar, then click on the link that says private messaging.
    Thanks but did that 3 weeks ago with no reply.
    The E-tugging force is strong my son. You might be the gifted one

  5. #5
    Join Date
    Feb 2005
    Location
    Florida
    Posts
    802

    Default

    Funny thing is..I havnt had any complaints before this
    I am wondering if you have your settings set ok in your control panel.

    I PM'd you this morning at 6am
    Did you get that one?

    I just sent you another PM Richey..hope you got it..


    If not .. try our email : maxyzmodules at yahoo dot com
    "My signature has been taken, so Insert another here"
    http://repairfaq.ece.drexel.edu/sam/laserfaq.htm
    *^_^* aka PhiloUHF

  6. #6

    Default

    Quote Originally Posted by marconi View Post
    Funny thing is..I havnt had any complaints before this
    I am wondering if you have your settings set ok in your control panel.

    I PM'd you this morning at 6am
    Did you get that one?

    I just sent you another PM Richey..hope you got it..


    If not .. try our email : maxyzmodules at yahoo dot com

    thanks for the reply, i got your pm's

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •