Results 1 to 9 of 9

Thread: Help! Cooling and mounting advice!

  1. #1
    Join Date
    Jun 2008
    Location
    Stockholm, sweden
    Posts
    352

    Default Help! Cooling and mounting advice!

    Hello Ppl!

    I have finally recieved my Alumium bar that i will use to cool and mount my Axions diode mounts in.

    But i have 2 options to do this and would like to know what you guys think how i should do it.

    The bar is 20cm wide and 4cm in height! the deep is 2.3Cm. (see drawing below)

    The option "One" is the easiest i think but i am not sure if that would give me the maximum cooling option. The option "2" Covers more of the Axions but on the other hand a thiner layer will cover them. (see below drawing)

    hope to get some advice

    (What im going to do is to have 5 PHR Blue ray diodes in the axions and drive them in about 100-120mW)

    Thank you.
    REgards.
    /Rickard

    PS: sorry for the bad drawing but doin this post in a real hurry (babe is calling from the kitchen/bedroom
    Attached Images Attached Images

  2. #2
    Join Date
    Dec 2007
    Location
    Nottingham, UK
    Posts
    2,849

    Default

    I don't know what an 'axion' is, but assuming it's a diode housing, I would go for option 1, based on the fact that there will be more aluminium bulk around the actual diode, thus better heat transfer. Option one will be easier to drill.
    Also, option 2 doesn't leave much side wall thickness for the modules, i.e. if the drill angle isn't fully perpendicular you run the risk of drilling through into another side
    You should get away with option 2 on a pillar drill, but I'd still go for option 1.

    Dan

  3. #3
    Join Date
    Jul 2007
    Location
    west sussex uk
    Posts
    2,280

    Default diode mounts

    i think he means aixiz mounts for his lasers.
    the bar seems like a good idea but how do you plan on isolating/insulating
    each mount from ground, the diode mounts can not have any electrical contact to the bar or each other ? as most diode drivers drive from ground
    and if any of your diode mounts touch that bar or each other they will draw full current and go pop, i learnt the hard way and popped a few

    option 1 is ok as only the front 10mm of an aixiz mount is any good at removing the heat

  4. #4
    Join Date
    Dec 2007
    Location
    Nottingham, UK
    Posts
    2,849

    Default

    How about using an LM317 driver? That uses the same common ground for both the drivers and diode doesn't it?
    If not, you either have to coat the inside holes with lacquer, or 'sandwich' them with layers of plastic, however this would reduce you heat-sinking power considerably...

  5. #5
    Join Date
    Jul 2007
    Location
    west sussex uk
    Posts
    2,280

    Default diode mounts

    i think the best option if your going to use that bar is to go with option 1 then drill and ream the holes .5mm larger than the diode mounts
    then cut the whole thing in half (length ways) then in the gaps on one half drill holes and on the other drill and tap holes then wrap diode mount
    in heat transfer sheet cut to size then you can clamp them in to place
    this method allows for easy movment or replacement of diodes
    i take it that you will be lining all these up through a pbs cube
    and adjustable mirror mounts
    good luck with that it is not easy it hard work
    with the losses involved five 150 mw lasers you will at best get
    500mw final output
    go here and you can see what i made,
    http://www.photonlexicon.com/forums/...ead.php?t=4688
    the biggest problem you will have is getting the mirror mounts
    stable, have a habit of moving with the slightest temp change
    i also advise you get the holes, and the half cut done at a machine shop

  6. #6
    Join Date
    Jan 2008
    Location
    Belgium
    Posts
    1,009

    Default

    The blueray diodes do not have the cathode tied to the case if I'm not mistaking ...

  7. #7
    Join Date
    Jun 2008
    Location
    Stockholm, sweden
    Posts
    352

    Default

    Thnx for all the answers.

    To be honest i dont really know what the "cathode" means in swedish.

    But if it is the 3:d pin that comes out of the diode i will not use it. Only - and + pins will be used.

  8. #8
    Join Date
    Jan 2008
    Location
    Belgium
    Posts
    1,009

    Default

    kathode = -

  9. #9
    Join Date
    Dec 2007
    Location
    Stockholm, Sweden
    Posts
    556

    Default

    The cathode or the anode is tied to the case of the diode on some diodes but fortunatly not on the bluray types I've seen.

    I think option 1 is best and if you need more cooling the cut a piece of heatsink and screw/thermal glue it to the top of your mounting bar, you could use a fan also.

    If you want I have a sh!tload of pentium 4 coolers, both regular "passive" and heatpipe ones, you could have a couple for free if you need them.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •