Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 31

Thread: Laser blanking

  1. #21
    Join Date
    Feb 2009
    Location
    Benidorm, Spain.
    Posts
    145

    Default

    Wait, I just figured it out . I think I better get some sleep before I fall on my keyboard, it is nearly 2 a.m. here.

  2. #22
    Join Date
    Jan 2006
    Location
    Charleston, SC
    Posts
    2,147,489,632

    Smile

    Hehe... Always the language barrier to consider. But yeah, you've got it hooked up correctly. And if you have problems with the blanking being reversed, Steve was suggesting a way to fix that. But we already know that you don't have this problem, based on your earlier tests, so you're all set!

    Adam

  3. #23
    Join Date
    Feb 2009
    Location
    Benidorm, Spain.
    Posts
    145

    Default

    Hi,

    I've just this minute hooked up the diodes to the mod outputs as Adam discribed but it doesn't seem to be working. I can see the full patterns and the retrace lines.

    I've tried measuring the voltage at the mod imput on the laser to see if it was receiving the signal and I get arround 6 v.

    Domingo.

  4. #24
    Join Date
    Jan 2006
    Location
    Charleston, SC
    Posts
    2,147,489,632

    Cool

    Sorry for the late reply, Domingo - still catching up on the backlog!

    Something is very wrong. You should not ever see 6 volts on the modulation line. Also, how are you measuring that voltage? A multimeter will only give you an average value. To check the voltage correctly you need an oscilloscope.

    But there's no excuse for 6 volts! Either you've got a wire connected wrong, or there's a problem with your DMX controller. Double-check your wiring, and post pictures if you can.

    Adam

  5. #25
    Join Date
    Feb 2009
    Location
    Benidorm, Spain.
    Posts
    145

    Default

    No problem Adam, I just got back from a 6 day holliday so I haven't been able to do anything anyway.

    Ok, I think I'm going to try simplifiying things a bit, I feel that I'm jumping in too deep to start off with. Let's see, I've disconected the DMX board alltogether and I've tried getting the ilda test pattern to display correctly (with blanking) using Spaguetti and only the X, Y and G pins from the correction amp connected directly to the scanner amps and laser.

    I can get the scanners to display the ilda test pattern more or less correctly (tuning it right is another matter), but there is no way of eliminating the retrace lines. Neither connecting or disconnecting the blanking makes any difference . I've tried tweaking the pots on the correction amp for the G signal, but the only thing I can achieve is to either only see the retrace lines or not see anything at all by modifiying the offset pot. I tried measuring the voltage on the G signal with my multimeter (I don't have an osciloscope) and I get an average of 3.04v.

    Any ideas?

  6. #26
    Join Date
    Jan 2006
    Location
    Charleston, SC
    Posts
    2,147,489,632

    Question That's strange...

    I'm not that familiar with the sound card DAC correction amp. From the sound of things, I'd guess that your gain is set really low, so you have to crank the offset up to get light, but when you do, the signal and blanking are at nearly the same level, which is why you can see the retrace lines.

    I'm guessing that you adjust gain by using the volume control on your computer, but like I said - this is unknown teritory for me. Maybe someone else can chime in here who is more familiar with the correction amp for sound cards...

    Adam

  7. #27
    Join Date
    Nov 2007
    Location
    Cairns, Australia
    Posts
    1,896

    Default

    drlava would probably the best one to help here, but my quick input:

    There was a max.wav sound file drlava created that lets you "tune" your sound card DAc correction amp. You need to tune it so that when is is PLUGGED IN, but NOT playing anything, that you have exactly 0V on your correction amp output. Then play the max.wav file, and adjust the (Gain I think ..) till you get around 5V. when you stop the file from playing, you should see 0V, when it is, 5V.

    Also make sure you have your sound card set to do 6 or 8 channels, otherwise it will try to merge them and disable some of the outputs. Another thing could be that your laser wants modulation on the - line, not +, but if I read Adams post above correctly, apparently that isnt a problem. Let me know if you want/need the max.wav file


    Good luck

  8. #28
    Join Date
    Feb 2009
    Location
    Benidorm, Spain.
    Posts
    145

    Default

    Hi Dan, thanks for joining in.

    Ok, I've set the pots on the correction amp for the G channel using the "max.wav" file and still nothing. As soon as i connect the blanking cable to the laser it switches off completely.

    I'm going to pm drlava to see if he can shed some light over the matter.

    Not sure if it means anything, but quite a few times, after I opened spaghetti for displaying the ilda test pattern and closed it, the 0v had moved down to arrount -4,60v and I had to open the "max.wav" file in Windows Media Player and close it for it to go back to 0v. Also, after I test the results of setting the pots on the correction amp by displaying the ilda pattern in Spaghetti, the 0v and 5v measurements seem to vary. Sometimes it's only arround 0.04v and others up to about 0.12v.

  9. #29
    Join Date
    Oct 2006
    Location
    Cleveland, Ohio
    Posts
    2,342

    Default

    A few things when you tune your correction board with the max.wav.. Your system volume and wav volume and playback volume should all be at max. Also the sound card control panel must be at 6 or 8 channel. You can test it by pressing the play button at the bottom right. After you have done this, set the DAC audio card to secondary in the windows audio settings control panel.

    Now, in your spaghetti scanner settings, under audio DAC click the More button and chose the right sound card, and invert red, green, and blue signals, and intensity if you are using it (invert X and Y as necessary). For the channel assignments I use (X Y R G B I AL AR):
    4 3 1 2 7 8 5 6, but you can set them to anything to match your wiring.

    Hope this helps!

  10. #30
    Join Date
    Nov 2007
    Location
    Cairns, Australia
    Posts
    1,896

    Default

    Interesting ...

    On my sound card, I have somehow managed to blow channel 3, so I am getting a NEGATIVE idle signal from the card, on that channel, instead of the usual 2.25V. I also get around -4 from the correction amp. Maybe the channel you are trying to use is dead?

    Can you try a different channel?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •