Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 38

Thread: LaserWave + Scanpro issue

  1. #21
    Join Date
    Jan 2006
    Location
    Charleston, SC
    Posts
    2,147,489,632

    Default

    Quote Originally Posted by mrblack927 View Post
    With 15v from the scanpro PSU applied to the op amp, the laser does indeed light up to full power when the rig is turned on.
    Did you also connect the -15V rail to pin 7 of the op-amp?

    Adam

  2. #22
    Join Date
    Jan 2009
    Location
    Buffalo, NY
    Posts
    65

    Default

    Quote Originally Posted by dave View Post
    I dont suppose you have access to an oscilloscope?
    Nope, sorry... What would you like me to check with it? the mod signal? I have a blu ray laser with a flexmod analog driver that I swapped in to test the signal and it works fine. Don't know if that helps though...
    EDIT: that's the signal from the scanpro board only... NOT the signal after the op-amp, don't know if I could test it that way... thoughts?

    Quote Originally Posted by buffo View Post
    Did you also connect the -15V rail to pin 7 of the op-amp?

    Adam
    Actually yes, but that didn't work. When I connect pin 7 to the scanpro -15v, the laser turns completely off when the rig is on. When I connect pin 7 to the scanpro ground, it stays full-on when the rig is on...

  3. #23
    Join Date
    Jan 2009
    Location
    Buffalo, NY
    Posts
    65

    Default

    update:

    I thought I'd take a picture and make sure we're all on the same page.

    The wires:
    Black: gnd from PSU (or -15, see above post)
    Red: +15 from PSU
    Yellow: +mod from scanpro set
    Green: +mod to laser



    So... is that hooked up right? or am I doing something wrong here

    Thanks!

  4. #24
    Join Date
    Nov 2005
    Location
    Melbourne, Australia
    Posts
    3,702

    Default

    that looks ok.

    let me have a look at the program board i have later and work something out
    KVANT Australian projector sales
    https://www.facebook.com/kvantaus/

    Lasershowparts- Laser Parts at great prices
    https://www.facebook.com/lasershowparts/

  5. #25
    Join Date
    Nov 2005
    Location
    Melbourne, Australia
    Posts
    3,702

    Default

    Still haven't had a chance to look into this... Haven't forgotten tho
    KVANT Australian projector sales
    https://www.facebook.com/kvantaus/

    Lasershowparts- Laser Parts at great prices
    https://www.facebook.com/lasershowparts/

  6. #26
    Join Date
    Jan 2009
    Location
    Buffalo, NY
    Posts
    65

    Default

    That's alright!
    Take your time, I appreciate your help.

    I am very surprised that this has never come up before though. I mean, the SP20's are a very popular scanner, and Laserwave is a very popular laser brand... No one has ever tried putting the two together before?

  7. #27
    Join Date
    Jan 2009
    Location
    Buffalo, NY
    Posts
    65

    Default

    Anyone else have any potential ideas? Anyone think it would help if I got a better DAC? I mean, is the analog laser signal is just too weak right? Is that a problem with the DAC or the scanpro set?

    Thanks!

  8. #28
    Join Date
    Nov 2005
    Location
    Melbourne, Australia
    Posts
    3,702

    Default

    Quote Originally Posted by mrblack927 View Post
    Anyone else have any potential ideas? Anyone think it would help if I got a better DAC? I mean, is the analog laser signal is just too weak right? Is that a problem with the DAC or the scanpro set?

    Thanks!
    On it now
    KVANT Australian projector sales
    https://www.facebook.com/kvantaus/

    Lasershowparts- Laser Parts at great prices
    https://www.facebook.com/lasershowparts/

  9. #29
    Join Date
    Jan 2009
    Location
    Buffalo, NY
    Posts
    65

    Default

    Phew, well, I believe we can bring this thread to a close...

    As it turns out, I was using a faulty wire (how does that even happen) and getting false results because of it. As soon as I tried a different wire, the op amp circuit worked perfectly!

    So I'd just like to give a big thanks to everyone who helped out with this problem. I can't wait to REALLY test out my new laserwave lasers!

    Thanks again!

  10. #30
    Join Date
    Sep 2007
    Location
    Cape Town, South Africa
    Posts
    95

    Default

    Sorry to open this one up again, but as the modulation voltage is 5 and you are putting 15v through the opamp, doesnt that mean the laser is getting a 15v signal instead of 5v? Cant that damage the laser driver?
    My new module is on its way, so i just want to make sure before it gets here...

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •