Page 1 of 2 12 LastLast
Results 1 to 10 of 17

Thread: Shimming and alignment

  1. #1
    Join Date
    Feb 2008
    Location
    East Sussex, England
    Posts
    5,248

    Default Shimming and alignment

    Ok, so i'm not far off being in a position to get my new greens and scanners to retrofit my 2 store bought projectors (basically a rebrand of the Super 1 lasers available from China)
    http://cgi.ebay.com/300mW-532nm-Gree...03105007r19382

    Originally fitted with what appear to be Scaneco12 and scaneco15 scanners (bought at separate times so varying components) and ~100mw ttl lasers will be putting in 150mw Laswerwave and DT25's

    Obviously this is likely to require some shimming to get the alignment right.

    IS there a right or wrong way to go about this? I don't have accessto machine shop so could do with hints on best way to go about it. I'm guessing some thin ally sheet might do it providing i can get required thickness (thinness)
    Do the components need to have a good contact area with the base plate for heat transfer?

  2. #2
    Join Date
    Dec 2007
    Location
    Nottingham, UK
    Posts
    2,849

    Default

    Have you considered using copper sheet?
    New it's expensive, but if you have bits lying around they could be useful for shimming in, as they come in a variety of thin swg sizes. As well as having one of the best thermal conductivities.

    If that route doesn't work, let me know if I can help you out on the machinist side of things
    Lathe, CNC miller etc. you know that sort of thing

    Dan

  3. #3
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    machine shop supply places sell brass, steel, and plastic shim stock, and then you can use heatsink grease or silver loaded grease, or silver epoxy if you really need additional heat conduction.

    So you are looking for "shim stock" comes in thousandths of a inch in the US, ie 3 thou, 10 thou, 30 thou, 60 thou etc.

    Dont know how they do it in metric, but it will be similar.

    Its cheap and you can usually cut it with sharp scissors or a paper cutter if you get the brass or plastic.


    I dont know what their overseas shipping would be, but I get mine from Small Parts, www.smallparts.com. Small parts is a tad expensive. I also get it from McMaster Carr, and I'm sure there is a similar company in the UK.
    Steve
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

  4. #4
    Join Date
    May 2008
    Location
    nerdtown, USA
    Posts
    1,165

    Default

    You can get pretty good results by taking a box cutter to an empty drinks can; it's best to strip the paint before you cut it up, then once it's cleaned up you can cut it to get one largeish rectangular piece, which flattens well under a pile of old Mauser and Edmund Optics catalogues. Comes in steel (tougher) and aluminium (better thermal conductivity, don't strip with caustics or it'll dissolve)

  5. #5
    Join Date
    Mar 2008
    Location
    Canton, GA USA
    Posts
    384

    Default

    Cheapest, best, quickest way to get a bunch of different thicknesses of shim stock is to go to any auto-parts place and buy a feeler gauge set like this:

    http://www.amazon.com/Grizzly-G9616-.../dp/B0000DD0IX

    Get the kind that has the screw at the pivot. You can remove whatever thickness you need.

    They typically are available with thicknesses from 1-2 thousandths up to 30-35 thou.

    If you need smaller pieces, don't use scissors or wire cutters because they distort the edge. I use a grinding wheel on a Dremel tool to cut out the piece I need.

    Tim

  6. #6
    Join Date
    Feb 2008
    Location
    East Sussex, England
    Posts
    5,248

    Default

    Thanks for the pointer about the feeler guages, they'll be nice and accurate

    Can i get away with shimming just where the mounting holes are though, or do i need to make up shims that cover the whole underside of the head in order to maximise surface area to conduct heat to the base plate?

  7. #7
    Join Date
    Dec 2009
    Location
    Seattle, Wa
    Posts
    413

    Default

    Just found this old thread, thanks for the great tip on shim stock. Amazon has a nice copper assortment for $30. I had been ordering aluminum shims from a machine shop but couldn't get the right thickness.

    Thanks,
    Mike

  8. #8
    Join Date
    May 2007
    Location
    Romania
    Posts
    1,041

    Default

    If your considering shimming heads:

    Get brigs to mill down the scan block or base plate and then don't need any shimming on heads. Adjust the scan block height not the head heights which causes problems.

  9. #9
    Join Date
    Dec 2009
    Location
    Seattle, Wa
    Posts
    413

    Default

    The source of my height adjustments are that all 3 laserwave modules have different heights. The green is the biggest so I have the other two lasers and the scan block on shims. I do think I need to learn how to mill stuff though...

  10. #10
    Join Date
    Oct 2010
    Location
    Athens, Greece
    Posts
    1,930

    Default

    well, as already stated, this is a 2009 thread.

    I believe in the meantime norty has implemented beam steering via bounce mirrors and is now an overall happier man

    "its called character briggs..."

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •