Page 2 of 2 FirstFirst 12
Results 11 to 19 of 19

Thread: YAG Coolant Advice

  1. #11
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    congradulations! How is the diameter and divergence?

    Steve
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

  2. #12
    Join Date
    Apr 2006
    Location
    Wirral, UK
    Posts
    191

    Default

    Quote Originally Posted by mixedgas View Post
    congradulations! How is the diameter and divergence?

    Steve
    'Bout 0.2mm dia. and 15 degrees divergence (straight out of an endoprobe)

    Ended up pulling the AO driver and running it connected but lid off.
    RF was picked up on a wire loop but the scope aliased the 27MHz.
    Should have selected peak detect mode on the scope but too late now.

    Hook up info for CTI 1027-25 AO Driver ...

    24V supply ---- Violet=0V, Yellow=+24V.

    J801 is the control input. On the Alcan only the top row of pins are used.
    Reading from left to right..
    Pin5 - Red Wire
    Pin6 - Orange Wire
    Pin7 - Yellow Wire
    Pin8 - Green Wire

    Pin5 is a NC in the Alcan service manual.

    Pin 7 is connected to +5V
    Pins 6 and 8 have 330R resistors in the loom by the connector.
    The other side of the 330 is pulled down to the 0V return of the +5V supply via open drain FETs on the main controller card.

    Pin 7 (yellow) goes to Pin1 of U8 and Pin1 of U9 - this is the anode supply to the LEDs in both OPTOS
    Pin 6 (orange) goes to Pin 2 of U9 - Cathode of U9 OPTO LED.
    Pin 8 (green) goes to Pin 2 of U8 - Cathode of U8 OPTO LED.

    Grounding pin 6 - orange wire (please note by grounding I don't mean taking to the 0V of the incoming 24V supply I mean taking to the 0V return of the 5V supply going into Pin 7. (obvious to Steve but maybe not to onlookers))
    Grounding pin 6 causes the bursts of RF as shown in Alcon_Ready_1_U9p6_2_RF.JPG
    RF on for approx 70us, off for 8us or so.

    On the Alcan the lamp is enabled all the time you are in the ready mode. Pin 6 is grounded causing the driver to output bursts of RF but there is no 532 laser o/p until you hit the peddle.
    When you hit the o/p peddle there is a click from within the laser head (mechanical beam block being moved) and there is laser o/p. There is no change to the o/p of the AO driver !!

    When you release the peddle Pin 8 (green wire) gets pulled low for between 50 and 100 ms (seemingly random between these times) there is a click from the head and the laser o/p stops (beam block being replaced??)
    Grounding Pin 8 causes U8 to turn on, making the opto Pull U9p6 low. This causes the RF amplitude to increase. During the increased RF stage there is no break in the RF waveform. See Alcon_Ready_1_U8p6_2_RF_20ms.JPG

    I guess this is to fully stop any laser o/p whilst the beam block is replaced.

    This infers the following functionality for J801

    Pin 8 - Mode, NC=self oscillating 12.5kHz Pulsed RF for Q-switched drive - amplitude set by RF low POT?
    Pin 8 - Mode, pulled low via 330R resistor - Full CW RF, not pulsed - amplitude set by RF high POT?
    Pin 7 - +5V supply, common Anode connection to both OPTOs.
    Pin 6 - Enable, NC=disabled
    Pin 6 - Enable, pulled low via 330R resistor - RF enabled, mode as set by Pin 8.

    Hope this is of use.....
    Robin.
    Attached Images Attached Images
    Lasers and beer don't mix. After 2 beers I lose coherence.

  3. #13
    Join Date
    Apr 2006
    Location
    Wirral, UK
    Posts
    191

    Default

    Almost forgot.
    Nice RS232 Diags ;-)

    prog en PROM
    
    PROGRAM YAG2 - Version 6.02 KAL/PJG/JMT/DA - 09 Jun 95
    様様様様様様様様様様様様様

    ? For HELP. PROM ok. RAM ok.
    Machine Configuration - PORT2 KTP CRYSTAL. UnModified Board
    Verifying saved calibration data...

    Verifying 4 / 20 mA sensors...
    Initializing HeNe motor position...
    Initializing power tables...
    Search K.T.P crystal curve
    Motor starting position (warm-up) 650
    Search for the crystal maxima
    Green power curves Acquisitions :
    Motor position after 150 mW 440
    Current = 16000 mA : Power Max at 1240 steps - 839 mW
    Current = 17000 mA : Power Max at 1240 steps - 1051 mW
    Current = 18000 mA : Power Max at 1200 steps - 1536 mW
    Current = 19000 mA : Power Max at 1280 steps - 2012 mW
    Current = 20000 mA : Power Max at 1400 steps - 2704 mW

    Min 0 mW @ 16000 mA Max 2704 mW @ 20000 mA.
    Initialization Duration = 95298 msec
    Lasers and beer don't mix. After 2 beers I lose coherence.

  4. #14
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    WOW, Thanks for Reverse engineering the Qswitch.



    Steve
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

  5. #15
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    Current = 19000 mA : Power Max at 1280 steps - 2012 mW
    Current = 20000 mA : Power Max at 1400 steps - 2704 mW

    Min 0 mW @ 16000 mA Max 2704 mW @ 20000 mA.
    Initialization Duration = 95298 msec[/QUOTE]


    In the US its got to be 3.2 Watts +20/-10% at 18A to legally be in service.

    Sounds like it needs a peak and clean, or heaven forbid, a new lamp.

    Pump chamber is white ceramic on mine,so no need to worry about missing gold on the reflector. Also no flow tube to go south.

    I'd look at the lamp I/V curve vs the PE=EG&G stats for that lamp. If you ask PE nicely I'm sure they will send you a more accurate curve then the one on the lamp datasheet.

    Does the RF ramp up on the first pulse for giant/first pulse supression or is the mechanical shutter intracavity on yours? Ie the slow mech shutter leaks just enough light as it slowly opens to kill the upper state storage in the rod or you ramp the AO open slowly on the first shot. Or maybe they did nothing at all?
    Steve
    Last edited by mixedgas; 06-22-2009 at 20:52.
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

  6. #16
    Join Date
    Mar 2008
    Location
    Sydney, Australia
    Posts
    315

    Default

    Hi Robin,

    Nice price on that machine, and nice work getting it greening.

    Hey, you're using the same Q-switch driver as me!
    http://www.photonlexicon.com/forums/...ead.php?t=7574

    Guess what, I found the original manual for 1027-25!
    http://external.weartronics.com/aoqs...er_1027-25.pdf

    Best regards,

    weartronics

  7. #17
    Join Date
    Mar 2008
    Location
    Sydney, Australia
    Posts
    315

    Default

    Quote Originally Posted by uk-laser View Post
    I have plenty of auto grade DI water.
    Obviously it depends entirely on your source, but I recently measured the auto grade "deionized" water from various places around here. All were ~20 uS/cm (~5 kohm.cm), which is pretty bad for direct exposure to arc lamp contacts. It will interfere with the lamp triggering, and long term exposure to the quartz is probably bad too.

    Quote Originally Posted by uk-laser View Post
    A bit dubious about its resistivity I'll have to build a cell to measure it.
    I bought one of these cheap meters off eBay. The range is not ideal for this application, but excellent water measures 0, good water measures 1, and auto grade deionised water measures 20 (the meter reads directly in uS/cm). You can buy a meter with a more suitable range, but the price is more like $100 instead of $20.

    http://cgi.ebay.com/ws/eBayISAPI.dll...m=270409478840

    Quote Originally Posted by uk-laser View Post
    If unsuitable then work has a distilled water plant so I should be able to beg a gallon or two.
    If you get very high resistivity water (e.g. fresh from a still), don't put it directly in to your laser! Freshly distilled water has such a high affinity for most metals that it is effectively very corrosive! It will degrade e.g. the brass/nickel arc lamp contact springs very quickly. If you have a source for fresh distilled water, leave it exposed to the air for a few hours first, and it will rapidly drop to several megohm.cm. Laserscope recommends 500 kohm.cm, and most industrial Nd:YAG lasers I have seen recommend 1-3 megohm.cm.

    For the hobbyist who isn't fortunate enough to have a still at work, one way to obtain deionized water suitable for arc lamp applications is to start with relatively clean water (e.g. auto grade demineralised water, filtered drinking water, or even good quality tap water) and run it through a filter column with a 1 megohm.cm endpoint, such as:

    http://cgi.ebay.com/ws/eBayISAPI.dll...m=150353206933

    You also can buy similar filter column with hose stubs on each end, so you can just gravity feed it from a drum above and it trickles out the bottom. Your final conductivity will depend on the conductivity of the source water, and the flow rate through the filter. Also, at least using auto grade demineralised water instead of tap water will make the filter last a lot longer.

    Best regards,

    weartronics

  8. #18
    Join Date
    Apr 2006
    Location
    Wirral, UK
    Posts
    191

    Default

    Quote Originally Posted by mixedgas View Post
    WOW, Thanks for Reverse engineering the Qswitch.
    No worries. had to be done - for 2 reasons.
    Firstly - I couldn't find any info on the web at all.
    Secondly - you put in enough work and some smart a$$ will provide the full datasheet they just happened to have tucked away. Thanks Nic. ;-)
    Looks like I was close on the R.E. The only assumption I got wrong was what each operating mode was called. I assumed LOW mode was the pulsed mode and HIGH mode was the CW one. This I assumed because the RF power in CW mode was set HIGHER than in the pulsed mode! I will go back and edit the original post to correct this.
    Quote Originally Posted by mixedgas View Post
    In the US its got to be 3.2 Watts +20/-10% at 18A to legally be in service.
    If 3.2W +20%/-10% at 18A is in service it sounds very promising for 20A - 5 to 6W ?
    I'll hook up the laptop again and ask it for the lamp I V curves. I imagine the lamp is end of life.

    Quote Originally Posted by mixedgas View Post
    Does the RF ramp up on the first pulse for giant/first pulse supression or is the mechanical shutter intracavity on yours? Ie the slow mech shutter leaks just enough light as it slowly opens to kill the upper state storage in the rod or you ramp the AO open slowly on the first shot. Or maybe they did nothing at all?
    All the time the lamp is lit the RF is running in pulsed mode. When you hit the laser peddle you hear the click of a beam stop moving out of the way. The RF continues running in pulsed mode. There is no RF modification for first pulse suppression. I guess the mechanical movement is so slow in comparison to the storage time of YAG it does a good enough job.
    Interesting they drive the RF to full o/p (no pulsing) just before replacing the beam block. I guess dropping a block into a running q-switched beam could be detrimental to the block given time?

    Quote Originally Posted by weartronics View Post
    Guess what, I found the original manual for 1027-25!
    #%$$** ^%%!! ***$^% thanks ;-)

    Also thanks Nic for the very useful info on the DI / distilled water.
    I didn't realise freshly distilled could be so corrosive. I would have been tempted to dump it straight into the laser reservoir.

    BRs, and thanks for everyones help.
    Robin
    Lasers and beer don't mix. After 2 beers I lose coherence.

  9. #19
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    If 3.2W +20%/-10% at 18A is in service it sounds very promising for 20A - 5 to 6W ?
    end quote

    At my friends shop, I saw one do 6 at 20 and one do 6.5 at 20. I saw one on EBAY claiming 7 after laser show mods , but it was in Hawaii and I was not about to pay shipping from Oahu to Ohio. Now that was new lamp, and perfectly adjusted and computer behaving and no thermal drift. Of course one hour later or after putting the lid on, your mileage may vary, My friend told me about a third he could never get above 2 watts, too. I suspected cavity optics damage on that one. If way out of whack they mode hop and do TEM gazillion x trillion.


    So expect 4-5 and expect to have to move the crystal around a bit to get it.

    Good to know the GP is mechanical, I was thinking of ditching the shutter.l

    Your orings go out tomarrow.
    Have you figured out how to bypass that CPU and talk to the switcher directly? Not that I care, I dumpster stocked mine before I got a phone call offering me a partial manual. I'm using a ESKI when I find 2 24V 6 amp supplies. *&%#$@#%& *&^% isolated cooling pump is 24V DC. Argh.....

    BTW, there was a older version using a spining disk qswitch on a motor shaft, It looked like a fan blade with 32 holes.


    Steve
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •