Full color 600mw

[illimaista]

Hello!

Ive been searching laser for some amateur shows and logo projection and found this one from ebay.
• Laser : Diode Laser

• Wavelength: red 650nm@300mW
green 532nm@150mW
blue 472nm @ 150mW
• Color:
red,green,yellow,cyan,blue Violet,Magenta,white(mixed)
• Scanner: ILDA30Kpps,+/-30 degree
Controlled by auto sound active or DMX .Mater / slave,ILDA linkable fu2 (24 channels), PC software

• High capacity and speed microprocessor control
• Rotation, Zoom (+/-),Rolling, dot drawing and 3D Animation etc
• Interface: ILDA DB-25 connector (Use to control the exterior computer .When the ILDA interface connected to the exterior console,light will automatic change to exterior console,and need not to convert switch )
• Cooling method : Fan cooling
• Power supply: 120V, 60Hz

• metal casing : 640*304*266mm Net Weight : approx. 15Kg
• Have Key On/Off Switch,that can prevent unauthorized use and the DB9 plug can be used for remote control
• Applicable for Disco, Pub, Bar, Clubs, large stage, entertainment center, trade show, corporate special events, casinos,etc

Can Run VIA DMX or with included ITop Laser software

Looks good with or without Smoke/Haze.

Cost is 810$. Need some advise. I would use lt with Pangolin live pro and FB3 board. Im open to any advise or suggestions.


ILLIMAISTA

[allthatwhichis]

Post a link... This is NOT a Laserworld projector is it?

[soforene]

The phrase "When the ILDA interface connected to the exterior console,light will automatic change to exterior console,and need not to convert switch" is used a lot in Meierlight adverts.

How sad am I for spotting that !

[Doc]

The phrase "When the ILDA interface connected to the exterior console,light will automatic change to exterior console,and need not to convert switch" is used a lot in Meierlight adverts.

How sad am I for spotting that !

... and also says that the interlock loop is defeated and used to turn on the dmx function instead....

[White-Light]

I'm sceptical straight away simply because the 150mw 473 blue to buy costs $1280 (Laserwave) or 1/2 as much again as the price the whole projector is selling for.

Bearing in mind you've got a green, a red (also v. expensive), a case, a set of scanners, auxiliary bit s and bobs and it sounds too good to be true.

Admittedly its TTL looking at the colours you've listed ie. 7 colour only., but even that doesn't make up for the price difference on the blue.

[Steve Milani]

red 650nm@300mW
green 532nm@150mW
blue 472nm @ 150mW
galvos, DMX, etc. etc.

$ 810.00 only???????

Sincerely I think bad.....
As *white-light* already right said..... only the price for 150mw @473 (not 472...) is more than 1000 dollars.....

Keep away from it.

All the best.

[soforene]

Steady on lads ....

[mikkojay]

I am sure it is This One
It looks to be a LumaLaser, so maybe it could be varianced "easily"?
I wondered about that, but I don't see the model anywhere in the listing.
The videos show that the green is out of alignment somewhat, but it looks like it makes some OK beams (although it looks quite haze enhanced). The graphics examples kinda suck, but it may just be the ishow software, I don't know.
Also, the generic description, quote:
"Applicable for Disco, Pub, Bar, Clubs,..." is a generic description that looks like it was cut and pasted right out of any Chinese projector listing on ebay.
It also bears an uncanny resemblance to this projector (4th one down).
Look at the specs on that one, scanners and lasers. If I hadn't seen the specs on the ebay listing, I would have guessed 24k and about 200-300mw from what I saw in the videos.

Anybody else got any guesses?
-Mike

[illimaista]

...so meierlight and lumalaser are manufacturers what i should avoid? Buying theyr products would be a bad investment even for first laser....il brake lt anyway But what are chines lasers doing differently? Liftime is shorter? Bad quality?


Thanks

[White-Light]

BTW the ebay advert (just above the pictures) says he won't ship outside the US so as you're in Estonia you can't purchase it anyway. - if its set up in the auction as US only then ebay now blocks bids from anything other than a correct regional IP.

I had someone in France wanting to buy an item of me recently that I set up for UK only. As it was low value and I trusted the person I wsa prepared to let them bid but they reported to me that the auction wouldn't let them because they were not in the UK - they were desperate to get it but there was nothing I could do as you can't reset region after the auction has started.

As for the laser itself, hard to tell but I think its very dim, could it possibly be under power? If you look at the beams in the video, look at the green then compare it other videos of greens. It looks very washed out as do the other colours which seems to indicate a significant amount of "brightness" has been added to the video. Could just be it videoed badly and had to be boosted in post, but equally it could be that its dim. Have to wonder why they're selling it after just 20 hours.