Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: wiring 20k scanners

  1. #1
    Join Date
    Dec 2006
    Location
    Essex, UK
    Posts
    8,647

    Default wiring 20k scanners

    got some scanners ages ago from laserpic and i dont have a manual for them. laserpic have since changed there 20k scanners on there site.

    any clues on wiring them up??

    starting from left to right

    im assuming the two reds are 240v + and -, dont matter which way round.
    next is earth

    the next set plug straight into the scanner amps so thats fine.

    but at the very end there is a red and black wire not connect to anything what do they connect to?



    i need to get a pic of the drivers as i dont know where the ilda input goes, will sort that out tomorrow.
    Eat Sleep Lase Repeat

  2. #2
    Join Date
    Dec 2008
    Location
    swansea, UK
    Posts
    198

    Default

    as its the power supply my guess is that the red and black either act as a low voltage switch - i had a computer power supply once that had two little wires to turn the whole thing on.

    other than that it might be a power indicator or something

    so basically... i don't know. but i'm bored!

    maybe tracing the copper tracks on the PCB will reveal more?

  3. #3
    Join Date
    Jul 2007
    Location
    west sussex uk
    Posts
    2,280

    Default power

    hi andy its proberly just a 5v or 12v for powering extras ie fan or dmx board ect
    power it up and and measure it
    the build going ok ?

  4. #4
    Join Date
    Dec 2006
    Location
    Essex, UK
    Posts
    8,647

    Default

    that would be way to easy chris

    i was just making sure they dont need to be connected to the scanners in anyway.

    the build is going slow but ok thanks, there will be some more pics and updates weekend
    Eat Sleep Lase Repeat

  5. #5
    Join Date
    Dec 2006
    Location
    Essex, UK
    Posts
    8,647

    Default

    ummm something isnt right, ive wired the psu up and ives ticking and the led is flashing on and off.

    ive not plugged it into the galvo amps for obvious reasons. as there are no stickers anywhere on the psu i am unsure of the voltage its suppose to be outputting.

    ive never seen a psu like this before tick and the led flashes on and off.

    anyone got any thoughts?
    Eat Sleep Lase Repeat

  6. #6
    Join Date
    Nov 2005
    Location
    Melbourne, Australia
    Posts
    3,702

    Default

    ticking generally means its current limiting, or going over voltage and being crowbar'd.. Dead supply by the sound of it././.
    KVANT Australian projector sales
    https://www.facebook.com/kvantaus/

    Lasershowparts- Laser Parts at great prices
    https://www.facebook.com/lasershowparts/

  7. #7
    Join Date
    Dec 2006
    Location
    Essex, UK
    Posts
    8,647

    Default

    poo, dave do you have any info on the PSU. this one i have does not have a single label on it, so i know nothing about it.

    i spoke to laserpic and they said that its a 18v psu, but they now use 15v psu for the 20k scanners. they are sending me a replacement psu but its only 15v.

    im a little unsure they know what they are talking about?
    Eat Sleep Lase Repeat

  8. #8
    Join Date
    Dec 2006
    Location
    Essex, UK
    Posts
    8,647

    Default

    anyone offer any clues as to how to wire this 20k amp?

    the psu only outputs 15v but its plugged into the 24v socket, cos thats where the plug fitted.

    unsure of where i should be wiring the XY???

    Eat Sleep Lase Repeat

  9. #9
    Join Date
    Nov 2005
    Location
    Melbourne, Australia
    Posts
    3,702

    Default

    Well,

    Jp 1 looks like singnal input

    J1 looks like power output ( confirm with a multimeter)

    You should be able to work out the polarity of the power connector by tracing which pin is connected to each of the 7815 and 7915 regulators..
    KVANT Australian projector sales
    https://www.facebook.com/kvantaus/

    Lasershowparts- Laser Parts at great prices
    https://www.facebook.com/lasershowparts/

  10. #10
    Join Date
    Dec 2006
    Location
    Essex, UK
    Posts
    8,647

    Default

    Quote Originally Posted by dave View Post
    Well,

    Jp 1 looks like singnal input

    J1 looks like power output ( confirm with a multimeter)

    You should be able to work out the polarity of the power connector by tracing which pin is connected to each of the 7815 and 7915 regulators..

    just looking at power going to the amp im happy with it, it looks correct and seems to correspond with the writing next to each pin. you can see the connector pplugged in on the right is power.

    so its only wiring it to the 25pin parallel connector now.

    but you recon jp1 is siginal?
    Eat Sleep Lase Repeat

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •