Page 1 of 2 12 LastLast
Results 1 to 10 of 16

Thread: Does someone know this ½W green...?

  1. #1
    Join Date
    Jan 2008
    Location
    Copenhagen, Denmark
    Posts
    23

    Default Does someone know this ½W green...?

    Hi,

    A few years ago I bought a used green laser module from a guy here in Denmark. The output power should be 500mW, but I am very sure that it isn't. Unfortunately I have no possibility to measure the effect with a power meter. But compared with other lasers of mine, I would guess that it just sneaks up on 100mW .... maybe less. (Not even burn-hole-in-black-isolating-tape-test can be handled)

    When I lift the lid on the power supply, I can see that somebody has made a repair on the PCB. Have no idea what is done, but there are soldered on some resistors and some wires.

    I can see, that there are three wires connected to the modulation connector. Could it be, that it is a balanced input (+/-5Volt)? I've always just used +5 volt and ground.

    Do some of you recognize the module and possibly have a diagram of it? It would be a great help ...

    Best regards
    Steen

    Pictures....
    Attached Images Attached Images
    Last edited by Smeisner; 11-15-2009 at 13:07.

  2. #2
    Join Date
    Jan 2008
    Location
    Belgium
    Posts
    1,009

    Default

    Could that be a early model Viasho?

  3. #3
    Join Date
    Aug 2007
    Location
    Under a rock in Cambridge UK
    Posts
    1,353

    Default

    Looks like a Lambda Pro to me http://www.lambdapro.com/product.htm

    Mark
    Last edited by Insanity; 11-15-2009 at 14:57.

  4. #4
    Join Date
    Dec 2006
    Location
    Finland
    Posts
    44

    Default

    Yours has a same type number as my Rumzing 500mW green (RZG-500). I don't think anyone has messed up with the driver, I bought mine new, and internals look like that
    Head connector is different in my driver unit (15-pin D connector).

    I'd say the third wire is for recognizing the modulation connector, mine switches into modulation mode when the connector is plugged in, CW otherwise.

    Those are probably made by same Chinese manufacturer, just branded for the actual seller.

    I haven't had any issues with mine, but being a pessimist, I'm thinking it has probably been a lower spec laser which has then been sold as higher power unit. I wouldn't be surprised if it died any day. Luckily 532nm is pretty affordable in this range of power.

  5. #5
    Join Date
    Nov 2007
    Location
    Cairns, Australia
    Posts
    1,896

    Default

    Every laser is destined to degrade in power over time.

  6. #6
    Join Date
    Jan 2008
    Location
    Copenhagen, Denmark
    Posts
    23

    Default

    Things; Hmmm .... yea. Sounds like the seller has not been completely honest about the age and operating time on the device then.

    Mark; You are right. Specially their power supply LPS-1000 looks like mine - from the outside at least.

    I guess it's only the diode that burns out over years. Is it possible to exchange the diode only in such a unit? Or is it better/saver just to get a new laser module (incl. psu?

  7. #7
    Join Date
    Jan 2009
    Posts
    1,622

    Default

    DPSS lasers can go out at any time between their manufacture and their rated end of life. Normally they'll last for 10,000 hours or more, but their power will gradually degrade over that time. It's impossible to tell how old a system is by it's output. It could be years old or days old. It's not at all unheard of for a DPSS laser to die while still new.. fortunately those are typically covered by warranty.

    Don't get me wrong, DPSS lasers are reliable the VAST majority of the time, it's just that they can be finicky sometimes as well.

  8. #8
    Join Date
    Nov 2005
    Location
    Melbourne, Australia
    Posts
    3,702

    Default

    Lol at singnal, that has been the same since we once had Lambda Pro lasers many, many years ago
    KVANT Australian projector sales
    https://www.facebook.com/kvantaus/

    Lasershowparts- Laser Parts at great prices
    https://www.facebook.com/lasershowparts/

  9. #9
    Join Date
    Mar 2008
    Location
    Sydney, Australia
    Posts
    315

    Default

    Well, the mystery of the laser manufacturer is solved. But the real mystery is the angle tuning of the dichro in your fourth photo. Was that even supposed to be 45 degrees? If so, please tell us who did the coating so that we can make sure *not* to buy them!

  10. #10
    Join Date
    Jan 2008
    Location
    Copenhagen, Denmark
    Posts
    23

    Default

    Yea, the mystery of the manufacturer seems to be solved. Thank you, guys.

    I've searched a bit on Lambda Pro on the forum, but couldn't find anyone who have exchanged the pump diode on such a unit before. So I think I will go for a new greenie... a NEW one. Maybe later I'll try to find a new pump diode for this one, and use it in another projector. Can someone give a hint about what power level I should go for, to reach 500mW of green light output?

    The angle of the dichro is no mystery. Just look at the angle of the associated red laser. The angle is more like 65 degrees. The red is a 635nm and puts out a very fat beam. This angle makes it possible to hit the dichro (wich is only 15mm) without hitting the edge of the dichro mount. I could also have made a cut out in the dicro mount (or used a 25mm dichro). But my plan in future is to exchange the red laser, with one with better beam specs. Unfortunately I'm on a "one-thing-at-a-time-budget". Therefor I'm the owner of a "one-thing-at-a-time-projector". And right now the "one-thing" is green...

    :-) Steen

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •