New DMX RC-Servo and DMX TTL convertor boards from LSP

Printable View

02-21-2009, 00:10
dave

New DMX RC-Servo and DMX TTL convertor boards from LSP

Single channel DMX RC-Servo Driver

http://lasershowparts.com/images/DMXservosm.JPG

Pretty straight forward board. will drive your typical RC-Servo from DMX. There are jumpers to invert the servos position, and decrease the travel of the servo to 1/5th of its travel, making it useful as a poor mans GM20 ;) **servo NOT included**

A couple of uses that come to mind are using the servo to drop a grating down in front of a set of scanners, or as a cheap beam switch..

Manual here: http://lasershowparts.com/files/Manuals/DMX/DMX01S.pdf

$60AUD, with free shipping via airmail to PL members :)

Single channel DMX TTL decoder

http://lasershowparts.com/images/DMXttlsm.JPG

Even simpler than the servo board. Single channel DMX-TTL decoding, with a jumper to invert the output

Manual here: http://lasershowparts.com/files/Manuals/DMX/DMX01T.pdf

$50AUD, with free shipping via airmail to PL members :)

These ad to our existing boards, being a single channel, and 8 channel relay card, and a 16 channel TTL card.

:D
02-21-2009, 07:35
Stuka

Nice! :)

After a little testing today, I plan on posting some info for a "special" servo I found that would be perfect to use with these!!

How soon will the new offerings be available on the web site?
02-21-2009, 15:05
dave

Hey Randy,

Don't think Ill get a chance to get them up until next week,once I come back from a well earned holiday :)

I forgot to mention, I have sent one of each of DMX01S, DMX01T and DMX08R to both the UK and USA meets as door prizes :D Pitbull and Buffo know all about it :D
02-21-2009, 17:45
DjDevNull

I like the TTL board. But here is the servo board I have.

http://home.att.net/~northlightsyste...2toRCservo.htm

It can control 8 servos plus it works via serial too.
02-21-2009, 18:17
dave

8 channel board coming soon.. The firmware I actually wrote as 8channel firmware, then stripped it down to single channel..

I could quite easily add rs232 functionality for not much effort, but for laser use, I didn't see the point!
02-21-2009, 19:27
Stuka

Quote:

Originally Posted by dave

Hey Randy,

Don't think Ill get a chance to get them up until next week,once I come back from a well earned holiday :)

I forgot to mention, I have sent one of each of DMX01S, DMX01T and DMX08R to both the UK and USA meets as door prizes :D Pitbull and Buffo know all about it :D

No problem - enjoy your holiday!
And thanks in advance for the donation to FLEM!! :D

Quote:

Originally Posted by DjDevNull

I like the TTL board. But here is the servo board I have.

http://home.att.net/~northlightsyste...2toRCservo.htm

It can control 8 servos plus it works via serial too.

Same source I've been using, discovered "pre-Dave".
It's good to have options, expecially when Northlight Systems and LaserShow Parts are both such great companies to deal with! :D
02-22-2009, 07:03
Banthai

nice one dave

where you going then ? i can reccomend St Kilda or a couple of sleezy lap dancing bars in paramatta :D

have a good time buddy and enjoy
02-22-2009, 10:03
p1t8ull

Quote:

Originally Posted by dave

I forgot to mention, I have sent one of each of DMX01S, DMX01T and DMX08R to both the UK and USA meets as door prizes :D Pitbull and Buffo know all about it :D

Boards are already here and ready to d'sh out on the door, thanks again Dave and Aijii :)

Quote:

Originally Posted by dave

a well earned holiday

Earned indeed. Have a good 'un! :cool:
02-28-2009, 01:51
dave

Just a quick note -

I have a few of each built up and up on the store :)