Page 1 of 2 12 LastLast
Results 1 to 10 of 19

Thread: YAG Coolant Advice

  1. #1
    Join Date
    Apr 2006
    Location
    Wirral, UK
    Posts
    191

    Default YAG Coolant Advice

    Hi all,

    Bit out of my comfort zone here.
    I have acquired a little 3W lamp pumped 532 which requires DI water for coolant.
    The service manual mentions a chemical additive to maintain the high resistivity of the DI water.
    Any idea what this additive would be? (or if it is really necessary for short term use?)

    Cheers,
    Robin
    Lasers and beer don't mix. After 2 beers I lose coherence.

  2. #2
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    Sounds like you have a biophysiq /Alcon.

    really, all you need is a good DI filter, additives are rarely used.

    your targeting for 8 megohms per square of resistivity, ie not a perfect insulator, but one at least good enough to prevent leakage currents and hold off the ignite pulse.

    I'm rebuilding my alcon right now, just got in the impossible to get metric orings, and I'm just using a simple flow throughj DI cart. With the exception of a medical system, I've never seen additives used.
    Steve
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

  3. #3
    Join Date
    Nov 2007
    Location
    Michigan
    Posts
    97

    Default

    I don't use additives either. Pure DI from a DI filter. My system is a heat exchanger system with the primary heat removed via the DI to a coil inside a second tank of flowing city water.
    The Frothy Chimp
    Cynic Extraordinaire
    Back off man, I'm a scientist

    Good whiskey, fine cigars, long legged women and blues guitar.
    That's what I like.

    The strong shall stand, the weak shall fall by the wayside.

  4. #4
    Join Date
    Jan 2006
    Location
    Charleston, SC
    Posts
    2,147,489,632

    Cool

    Quote Originally Posted by uk-laser View Post
    The service manual mentions a chemical additive to maintain the high resistivity of the DI water. Any idea what this additive would be? (or if it is really necessary for short term use?)
    This is a new one to me, Robin. And I worked in the high-purity water industry for a few years.

    About the only thing that might work would be an alcohol or an ester... It would need to be a covalent, non-conductive substance... But I've never heard of anyone doing anything like this.

    Usually people just recirculate the water through the mixed-bed resin filter (the DI cartridge), and that keeps the water pure.

    Adam

  5. #5
    Join Date
    Apr 2006
    Location
    Wirral, UK
    Posts
    191

    Default

    Many thanks for your replies.

    Reading further in the service manual it calls it a "chemical pack".
    I'm now wondering if it is just a bag of DI resin to be left washing around in the water reservoir.
    I'll know more when I get access to lift the lid on the water tank.

    Quote Originally Posted by mixedgas View Post
    Sounds like you have a biophysiq /Alcon.
    Yup, - http://cgi.ebay.co.uk/ws/eBayISAPI.d...m=290323586827

    Quote Originally Posted by mixedgas View Post
    your targeting for 8 megohms per square of resistivity, ie not a perfect insulator, but one at least good enough to prevent leakage currents and hold off the ignite pulse..
    I have plenty of auto grade DI water. A bit dubious about its resistivity I'll have to build a cell to measure it.
    If unsuitable then work has a distilled water plant so I should be able to beg a gallon or two.

    Quote Originally Posted by mixedgas View Post
    I'm rebuilding my alcon right now, just got in the impossible to get metric orings, and I'm just using a simple flow throughj DI cart. With the exception of a medical system, I've never seen additives used.
    Steve
    Must admit I bought the laser dreaming of doing a diode pumped conversion - I have plenty of 60W unmounted bars.
    After picking up the laser I am less confident - there would be a lot of work involved in replicating the controller functions.

    Cheers,
    Robin
    Lasers and beer don't mix. After 2 beers I lose coherence.

  6. #6
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    I'm in the middle of converting its predecessor to manual using a 19" rack single phase lamp supply. All I need is simple interlocks, a stepper motor controller for the LBO, and a oscillator for the qswitch rate.

    If yours is intact and functioing there is a diagnostic rs232 port on the back side. basically hook a dumb terminal program to it, bridge a jumper and its suddenly a well documented, intensive diagnostic screen. Mine came with a dead main processor board, so I'm hacking the raw hardware for obvious reasons.

    And yes, the chempack is DI resin in a plastic guaze bag.

    You'll need to boost the cooling loop if you want CW.

    It changes output power by keeping the lamp current steady and then applying a mapped curve to the LBO rotation. There is a safety light loop, but it builds up a tuning curve in EEPROM at each startup.

    I have the alignment part of the manual, but thats it.

    A friend services them, but I don't know how much he can tell you under his ND.

    Lamps are about 50$ on ebay and its one of the two smaller Perkin Elmer QCW krypton arc lamps, either the 51 or 76 mm arc ( rough sizes from memorY) which are 110V and 220V single phase lamps. Mine uses the short lamp, but I extended the lamp block for the 76 mm lamp, which I could get.

    Perkin elmer has a excellent databook on the lamp family as a PDF.

    Do note that more then 4 minutes of CW HIGH RF burns out the qswitch
    driver if you start hacking.

    My main holdup is finding a big 24V transformer for the DC isolated cooling pump.

    lamp is ran at a constant 17 to 18 amps during calibration and a bit less during operation.

    To get the wierd french ring seals for the rod and the lamp I had to order 250 of each, so send me a PM and then a self addressed stamped envelope and I'll toss you a dozen of each. They are not international standard Orings, they are a metric seal.

    Keep the desicant bag fresh in the the LBO "box"

    alignment from scratch is a witch according to my friend, it seems there are tonnes of ways for it to lase, but only one does the right mode to get it down the fiber.

    You now know what I know, except for the US Patent number on the linear cavity. Oh, and before you panic, there is no LBO heater by design. The crystal is cut for just above room temp and type I phase matching.

    I'm told as much as 7 watts qswitched in test mode for very good or new setups.

    As it is, it is a low duty cycle laser , based on user selected power, lower settings = longer bursts. Oh, and my friend describes it as "Too damn smart for its own good" I'm gonna add a water to water exchanger for my needs.


    Steve
    Last edited by mixedgas; 06-18-2009 at 18:57.
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

  7. #7
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    Must admit I bought the laser dreaming of doing a diode pumped conversion - I have plenty of 60W unmounted bars.
    After picking up the laser I am less confident - there would be a lot of work involved in replicating the controller functions.

    end quote.

    Nope, a stepper motor controller for the stepper and a pulser/ GP supression for the Q switch. Overtemp and flow interlocks on the cooling, and the rod doping is low for effective diode pumping. This rod is almost transparent in color. But if you have a pile of 60 watt diodes, who cares if you need a extra one.

    Steve
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

  8. #8
    Join Date
    Apr 2006
    Location
    Wirral, UK
    Posts
    191

    Default

    Thanks for the comprehensive reply.
    Quote Originally Posted by mixedgas View Post
    If yours is intact and functioing there is a diagnostic rs232 port on the back side. basically hook a dumb terminal program to it, bridge a jumper and its suddenly a well documented, intensive diagnostic screen. Steve
    Dumped in a couple of gallons of DI this evening. Error 72 (Flow rate) was caused by a sticking flow sensor. Having freed that it ran cal (nice lamp glow down water pipes from head) then displayed "Check DR's Filter" Connected that, and it ran cal again then displayed "connect fibre to Green 2" I'm still waiting for the endoprobes to turn up (hopefully tomorrow)
    I'll hook up the laptop to it to check out the diagnostic modes but I want to have the fibre in when I do.

    Quote Originally Posted by mixedgas View Post
    I have the alignment part of the manual, but thats it.
    You mentioned you were converting its predecessor?
    The service manual I have covers Opthalas 532nm from 1994 onwards (ser nos. under 1000 made in France, over 1000 made in USA) I appear to have full schematics for all the Alcon made PCBs. If these would be of use I can PDF them.

    Quote Originally Posted by mixedgas View Post
    Do note that more then 4 minutes of CW HIGH RF burns out the qswitch
    driver if you start hacking.
    The manual lists 3 modes for the A-O in service - Pulsed, Blocked & Continuous.
    It quotes "Do not leave the AO module in Blocked for extended periods of time greater than 3 - 4 minutes)
    I thought full RF was Blocked. I was hoping for extended operation in CW.

    Quote Originally Posted by mixedgas View Post
    To get the wierd french ring seals for the rod and the lamp I had to order 250 of each, so send me a PM and then a self addressed stamped envelope and I'll toss you a dozen of each. They are not international standard Orings, they are a metric seal. .
    Many thanks for the offer - PM sent

    Quote Originally Posted by mixedgas View Post
    my friend describes it as "Too damn smart for its own good"
    Amen to that.

    Hopefully I will get it running over the weekend. Then the option is to either split the head from the trolley and add a secondary cooling system or go diode pumped. I also have a 2x2x12mm Nd:YAG rod which was intended for diode pumping. I would like to try this but guess the much shorter length of the rod will muck up the cavity lengths. I imagine to use this I would need a piece of undoped YAG or glass to make up the missing length of the"lens duct" as PSST would call it.

    Cheers again,
    Robin
    Lasers and beer don't mix. After 2 beers I lose coherence.

  9. #9
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    You mentioned you were converting its predecessor?
    The service manual I have covers Opthalas 532nm from 1994 onwards (ser nos. under 1000 made in France, over 1000 made in USA) I appear to have full schematics for all the Alcon made PCBs. If these would be of use I can PDF them.

    I tossed the alcon PSU and CPU after robbing parts. I'm going to use a lambda emi model ESKI supply.

    I need the AO hookup wiring, PDF would be fine.


    The manual lists 3 modes for the A-O in service - Pulsed, Blocked & Continuous.
    It quotes "Do not leave the AO module in Blocked for extended periods of time greater than 3 - 4 minutes)

    blocked must be full RF. All I know is my pal said pulse that qswitch or remove the drive for extended cw.

    Steve
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

  10. #10
    Join Date
    Apr 2006
    Location
    Wirral, UK
    Posts
    191

    Default

    I have green ;-)
    Took a few goes to get going. On the first run it Cal'd to give a max O/P max of 1W.
    Second run it Cal'd to give a max O/P of 2.2W. Further runs are still 2.2W
    Guess it needs some TLC.

    Quote Originally Posted by mixedgas View Post
    I need the AO hookup wiring, PDF would be fine.
    I scanned the schematic pages but there is insufficient info on them for connection.
    The schematic shows only 3 ways being used:
    Pins 8, 7 & 6 are used. Pin5 is NC. Pins 1,2,3,4 are not shown at all.
    Pin8 & Pin6 have 330R series resistors (looking on mine these are physically in the loom by the connector)
    The other end of the 330Rs go to the System controller PCB where they go to open drain outputs, the OD FETs are driven by OPTOs sitting on the O/P of 74S174s. The function of each OD output is not indicated.
    Pin 7 I have traced through to a +5V supply rail.

    Looking at my Alcon there are 4 ways in the loom to the 8W connector. Pin5 (NC) has a wire on it!

    The 24V I/P is by twisted pair wire direct into the driver. One yellow, one violet.

    Although the Manual calls up Crystal Tech Inc 276-242 the part fitted in my Alcon is 1027-25. Googling seems to show this was used on the Laserscope as well.

    Guess the easiest way forward is for me to drag the storage scope out of the loft and take a couple of traces on the 2 OD wires with the laser firing various pulse lengths.
    Any luck and I should be able to do this today.
    Lasers and beer don't mix. After 2 beers I lose coherence.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •