You're OK as long as your lasers don't go over 120 db.
![]()
Doc's website
The Health and Safety Act 1971
Recklessly interfering with Darwin’s natural selection process, thereby extending the life cycle of dim-witted ignorami; thus perpetuating and magnifying the danger to us all, by enabling them to breed and walk amongst us, our children and loved ones.
Yep.. That was the monster and the twins playing together... A couple of times it was a bit off, but not too much...It was quite a difficult show, we had a DJ a percussionist and a guitarist all playing together and not always perfectly in time with each other... I don't use the beat timers, but instead use the speed controls to get as close as possible to the beat. This gives a far less jerky output, but is more difficult, as you need to know all of your effects and how fast/slow they are. My workspace contains 12 full pages of effects, 1 page of colour cycles, 1 page of beam chasers and 1 page of key effects. So a lot to remember...
I don't have scanfail yet, I am awaiting the outcome of Dave's testing on the Experiance scanfail before I go out and buy anything...
Audience scanning in the UK is allowed, it is down to the local authority to make the decision wherever an entertainment license is in use... Some just say yes, some are more paranoid and say no and some require full risk assessment with MPE calculation. In the case of Cambridgeshire, where we have the university and therefore a lot of knowledgeable people regarding lasers, the authority involve the HSE and the HSE require risk assessment. I sent in some 30 pages of risk assessment along with full MPE calculations to the 1 x MPE and 10 x MPE standards. The HSE were happy with my calculation and allowed the shows to go ahead.
Mark
Last edited by Insanity; 10-05-2009 at 02:09.
You where no way scanning at 1 MPE and I think you weren't scanning at 10MPE either. maybe at the location of your laptop.
Did you measuere the power at the closest point of the audience?
My rough guess is 100x MPE
I can assure you that your rough guess is way off. Yes this show was measured at closest audience point and measurements witnessed, as are all of my shows. This show was below the 10xMPE level and as was said earlier in the thread, the camera used to take this video is old and only ever used to film lasers. It lets so much light in that it is now incapable of taking normal photographs. It therefore makes the light look that much brighter, now add the youtube conversion factors. In fact, watch the video again and you will see that nobody is illuminated with laser light at any point. It is just a case of the camera focusing on the light from the laser, which incidentally is also being washed out by the par cans above the control area.
It is very difficult to assume laser power by eye and even more so on a video, as different cameras show light in different ways.
Brash statements like this can be very damaging... All I can assure you of is that this show was calculated as safe, proven safe with measurements and duly approved...
Mark
Edit: Another point to note is that the video was not taken in HD, but was upscaled on my Mac which probably has huge effect on brightness
Last edited by Insanity; 10-05-2009 at 08:20.
I'm sorry my guess was wrong.
I have done a lot of testing with 1MPE and 10MPE, and i just know how dim 1MPE looks like, thats why I knew it could never be 1MPE.
You are right it impossible to guess the MPE from a video, But it just looked too bright to be below 10MPE.
Did you increased the divergence or lowered the power to get below 10MPE?
If you have done you homework properly my "brass statement" shouldnever damage your reputation.
1 x MPE does look very dim and undesirable, which is a lot of the reason ILDA is proposing the 10 x MPE standard.
I have a good camera for general photography, holiday snaps and the like and another older camera for filming lasers, as we all know what lasers do to CCD'sThat older camera just can't take pictures any more, I took a photo of the Eiffel Tower in Paris one evening and all it could manage was a bright blurred swirl of light
The video was taken with that camera, edited and upscaled with iMovie on the Mac and then destroyed by youtube's compression etc..
I have done a lot of shows over the years, some with John O'Hagan present and can assure you I have done my homework. The HSE in my area won't let a show go ahead without relevant correct calculations and insist on measurements to back the calculations up.
To achieve the correct levels for MPE, attenuation maps are used. Once again, you wouldn't think it, as the camera simply will not pick them up.
The reason I say such comments can damage reputation is the fact that people with little or no experience of laser technology viewing this forum could translate this as bad practise. Most people on here know me and know my experience of clubs and festivals, so hopefully they know I am a very safe and responsible operator...
Mark