Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 25

Thread: Stoney's First Build - 0,6W RGV with harp mode!

  1. #11
    Join Date
    Oct 2009
    Location
    Eindhoven, The Netherlands
    Posts
    921

    Default

    Time for a piece of updates, since this thread is kinda worthless without beam shots!



    I Gaffer-taped everything in place today for a little test run. I've removed the Y galvo for now, since the amps didn't come with enough cables to wire everything up. I've ordered matching plugs through RS and expect them to be in near tomorrow afternoon.

    The galvo amp is wired straight into the sound card, with HE-Laserscan off my laptop. Seems to work pretty OK, I might even leave it this way and do a few test shows until I have the correction amp fixed up. The galvo's input gain is cranked all the way to the right in this case, but the scan angle is more than enough.



    Scanning shot, the beam is not blanked here (since the TTL blanking circuit in my 532 has a strange habit of pulling all of my ground lines to a high level when I wire it up), scan speed is 20kpps at this scan angle.



    Here's a shot of it on the floor, I found out that scanning a bit faster than the galvos were specified seemed to hold OK and the beams were more crisp. The galvo's made 30kpps on this simple beam pattern, but they'll probably choke on more complicated graphics at that speed. I'll probably have a few tries when I've got the Y galvo wired up tomorrow.



    Here's a shot of me and the unit in its intended mode of operation. Currently this is still a bit of a mock-up, since I still need to work up the code for detection (Windows Bluetooth drivers are a mess!). When I have that done, time for a demo video that will wipe Stephen Hobley off the face of the planet.



    Here's a snap with the same pattern and the scan angle turned halfway back (instead of pegged at absolutely max). I seem to have a bit of overshoot on the ends, but I'm not sure if that's because of the high scan rate or just the fact that I'm running this thing at an insane angle. You don't really notice any effect in the beams, though.



    Here's a shot to give you an impression of the beam spacing, with the scan angle on halfway (about 12 degrees at the guesstimeter). This is enough for a 7-beam pattern, I might increase it a little if I want to do 9 beams (over a full octave) like Jarre's.

    The only light on the photos is coming from the laser reflecting from the ceiling. I'm already looking forward to seeing this baby run white light, the Laserwave dichros should be in early next week, but I'm scared to see the actual light coming from that... I hope I don't end up with burn marks on my ceiling plaster (or my hands, for that matter!)

  2. #12
    Join Date
    Oct 2006
    Location
    Central Florida
    Posts
    7,067

    Lightbulb


  3. #13
    Join Date
    Oct 2009
    Location
    Eindhoven, The Netherlands
    Posts
    921

    Default

    Quote Originally Posted by allthatwhichis View Post
    If you mean the images don't work, they definitely do on my end and they're hosted on my Photobucket album. So it's probably an issue on your end.

  4. #14
    Join Date
    Dec 2008
    Location
    swansea, UK
    Posts
    198

    Default

    yeah the pictures work fine for me too. great idea by the way!

  5. #15
    Join Date
    May 2007
    Location
    The Netherlands
    Posts
    291

    Default

    yea the pictures work fine here to

    and its great to see a other dutch build on here
    Do not look into laser with remaining eye
    Need laser repair contact me !!!!!!

  6. #16
    Join Date
    Dec 2008
    Location
    Southport, UK
    Posts
    2,746

    Default

    Looking good so far.

    Just a suggestion; I don't wish to sound namby pamby, but it seems like it would be ever so easy to accidently "take one in the eye", you might want to think about fitting a diverging lense and angle the beams slightly away from yourself and fit a step-on interlock that only arms the laser when you are stood in the safe playing position?

    Ian
    http://img62.imageshack.us/img62/3985/laser.gif

    Doc's website

    The Health and Safety Act 1971

    Recklessly interfering with Darwin’s natural selection process, thereby extending the life cycle of dim-witted ignorami; thus perpetuating and magnifying the danger to us all, by enabling them to breed and walk amongst us, our children and loved ones.





  7. #17
    Join Date
    Oct 2009
    Location
    Eindhoven, The Netherlands
    Posts
    921

    Default

    Quote Originally Posted by Doc View Post
    Looking good so far.

    Just a suggestion; I don't wish to sound namby pamby, but it seems like it would be ever so easy to accidently "take one in the eye", you might want to think about fitting a diverging lense and angle the beams slightly away from yourself and fit a step-on interlock that only arms the laser when you are stood in the safe playing position?

    Ian
    I'll definitely build in standard safety interlocks in the coming week, since I'll be running this thing as a standard ILDA projector as well. An adjustable bounce mirror will deflect the beams upward to make it project the harp, I can tweak the angle it's projecting by turning the mirror.

    The unit will have an 'interlock bypass' switch with a guard cap on the back, which bypasses the remote interlock if it's in harp mode, slamming the guard cap shut will disengage the interlock loop and shut off the laser.

    When in harp mode, I'll be the only one operating the unit, so any Darwin Awards are my own responsibility only.

    Edit: Got the diodes in the mail today, and I wired up the drivers for a little test run.



    Unfortunately my Bluray died out on me when I was adjusting the driver current and I gave the pot just a little turn too much. ... Well, at least now I have a spare set of collimation optics!

    My dichro's aren't in yet, so I might be able to source a new Bluray in the meantime. I only need the diode, so if anyone has a spare sled lying around, I'll be happy to spare a few dozen € for it.
    Last edited by Stoney3K; 11-06-2009 at 13:45.

  8. #18
    Join Date
    Oct 2009
    Location
    Eindhoven, The Netherlands
    Posts
    921

    Default

    OK, I'm working on getting the optics table sorted now, the Bluray will have to wait a few weeks until the € supply is replenished. The dichro's are still in the mail.

    In the meantime, I did a few chroma plots with the planned diode power distribution:



    The red seems to be quite dominant making the white mix almost a magenta-ish one. Still have to see that in real life, I can always dial the red down if i need to.



    Here's a little plot when I mix the same diodes with a lower power Argon head, like an ALC-60x. The spectral distribution was a bit of a guess, but ~100mW of argon makes the beam a lot more white than just RGV. The ideal power would be 150mW, which puts the spot right in the middle.

    Of course I need a head and an AOM, but it's a good idea to look into that in the future. The colour gamut is pretty good with the RG-Ar-V combo. The only piece I'm missing for complete colour coverage is a line in the 494-497 range (on the far left).

  9. #19
    Join Date
    Dec 2008
    Location
    Southport, UK
    Posts
    2,746

    Default

    If you are planning on using a dvd burner diode; the wavelength will be nearer 660nm, which improves the white balance somewhat.
    http://img62.imageshack.us/img62/3985/laser.gif

    Doc's website

    The Health and Safety Act 1971

    Recklessly interfering with Darwin’s natural selection process, thereby extending the life cycle of dim-witted ignorami; thus perpetuating and magnifying the danger to us all, by enabling them to breed and walk amongst us, our children and loved ones.





  10. #20
    Join Date
    Oct 2009
    Location
    Eindhoven, The Netherlands
    Posts
    921

    Default

    You're actually right about that (maybe the diode I bought was incorrectly specced at 650nm), it helps a little.



    (Luminous flux here is 43.5lm)

    Dialing the red diode down to 200mW and the violet to 220mW makes the white balance smack in the middle, but the luminous flux suffers a little (3 lumen or 10% less). The diodes will probably run cooler, though.



    When I want to balance it now, I only need max. 50-60mW of argon to get the white balance right. The beam intensity goes up to 52.8 lumens in that case.


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •