Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 24

Thread: Chameleon Technology ALC60x PSU problem, help?

  1. #11
    Join Date
    Jun 2008
    Location
    Yellowknife, NT, Canada
    Posts
    2,147,484,113

    Default

    See I tried that, but maybe it never got hot enough? I'll try it again at the weekend, too busy this week otherwise. Doubt that I was over cooling it and I still think that it's the power supply, but it's worth a try right?

    I'll let you know how it goes

  2. #12
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    Quote Originally Posted by Diachi View Post
    See I tried that, but maybe it never got hot enough? I'll try it again at the weekend, too busy this week otherwise. Doubt that I was over cooling it and I still think that it's the power supply, but it's worth a try right?

    I'll let you know how it goes
    DONT CHANGE THE COOLING IF YOU HAVE AT LEAST 250 CFM. Its in the PSU.

    You dont have enough anode voltage for the tube to light, which means the fets are damaged or the feedback loop is damaged.

    Steve
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

  3. #13
    Join Date
    Jun 2008
    Location
    Yellowknife, NT, Canada
    Posts
    2,147,484,113

    Default

    Okay then, how would I go about figuring out which part of the PSU is dead?

    Is there any chance that my higher line voltage could have damaged the PSU? It's 254VAC +/- 5V ( probably varies with load ). Never had problems with anything before, but would it be possible?

  4. #14
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    Quote Originally Posted by Diachi View Post
    Okay then, how would I go about figuring out which part of the PSU is dead?

    Is there any chance that my higher line voltage could have damaged the PSU? It's 254VAC +/- 5V ( probably varies with load ). Never had problems with anything before, but would it be possible?
    yes, that would be a possibility.

    dig out a omni 150R schematic from the FAQ and tell me which one you have, your psu is a very simplified and modified omni. But all the part numbers will be different.

    we'll work from there.

    Steve
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

  5. #15
    Join Date
    Apr 2005
    Location
    SOUTHAMPTON U.K.
    Posts
    1,357

    Default

    George hasnt been able to tie the probleem down to anything specific.

    However, he has given me a set of schematics for the power supply and given permission for them to be posted here. Hopefully these will assist in your diagnosis.
    Attached Files Attached Files

  6. #16
    Join Date
    Jun 2008
    Location
    Yellowknife, NT, Canada
    Posts
    2,147,484,113

    Default

    That's great thanks! I'll take a look at them!

  7. #17
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    Quote Originally Posted by Diachi View Post
    That's great thanks! I'll take a look at them!

    CS324 is obsolete. Impossible to get. I have a request into the company that bought Cherry and expanded the technolgy.

    Here is the data sheet.

    We will go through this slowly.

    This is very similar to a MWK supply (same chip)
    Not a omni150 ,uses hysteric mode vs regular PWM.

    See attached.

    Steve
    Attached Files Attached Files
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

  8. #18
    Join Date
    Aug 2009
    Location
    Bristol, England
    Posts
    333

    Default

    Is LED3 lit (gate drive) when the thing should be running?

    Is there ~380V across the main HV bus when the thing should be running?

    These two questions will very roughly isolate the probable problem area.

    Be careful in there, those caps will hold a lot of charge for some time after the power cord is removed from the wall, and being bitten will hurt (and could be fatal).

    Regards, Dan.

  9. #19
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    Be careful in there, those caps will hold a lot of charge for some time after the power cord is removed from the wall, and being bitten will hurt (and could be fatal).

    Regards, Dan.[/QUOTE]

    And unless you have a isolated scope, don't hook any line powered instruments to it, this is the class "hot chassis" problem. Battery powered floating stuff is fine.

    Steve
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

  10. #20
    Join Date
    Aug 2009
    Location
    Bristol, England
    Posts
    333

    Default

    Yep, just like working on a telly!

    I have a cheap Maplin battery powered LCD scope for exactly this sort of thing, it is profoundly nasty, but sometimes it becomes the weapon of choice.

    In all probability this is fixable with nothing more then a multimeter if we have to, an isolated scope (or mains isolating transformer) would help but is probably not essential.

    Regards, Dan.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •